Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2007 Hyundai Santa Fe Limited
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com. Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me. The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar. I added that alternate Step below in the instruction step. Hopefully I'm able to insert the image of each instruction set so that the Figures are visible. Its actually not that easy getting the rear rail covers off and its pretty easy to crack them. I'd recommend gently rocking the covers for a couple minutes in order to loosen them up. Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes. If you have questions, go ahead and contact me. I also took several photos of my install and that might be helpul. Cheers!
SANTA FE 2008 PIN U8210-28000 Cross Bar Assembly Installation Procedures
Kit Contents: • (2) Cross Bar Assemblies Required Tools: • Flat Head Screwdriver
1. Carefully unscrew and remove radio antenna. 2. Grasp the rear rail covers with both hands. Squeeze and pull up & inwards (toward the center of the vehicle) to remove covers. Take care not to break off the tabs by lifting the rear section of the cover first (Figure 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 2. - Alternate Method - Locate notch in rear of each cover to insert plastic pry bar. Remove cover by prying up (with tool) and lifting rear at 45 degree angle (Fig 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 3. Check assembly clips for damage and dislocation. Replace if necessary. 4. Open the lever on one side of front/rear cross bar. Gently set the cross bar, with the arrows facing forward, into the channel of the side rails (Figure 2). Guide both sides into the track. 5. To adjust cross bars, open lever and place cross bars in desired location. Close lever (Figure 3). Try to move bars forward/back until they lock into place. 6. Reinstall rear covers by holding cover at a 45 degree angle and inserting the front tab into the rear of the roof rack. After aligning, snap cover in place (Figure 4). Be sure that the rubber lip does not interfere with the covers, and that the covers are fully seated. 7. Reinstall the radio antenna. Note: To remove the cross bars, remove the antenna, remove the covers, open lever of cross bar and slide to end of rail. Hold down locking fingers (on both RH/LH rear rail supports) with a flat head screwdriver (Figure 5). This will allow removal of cross bars from the rails.
Posted on Feb 24, 2009
The above statement is GREAT!!! The wheel-well piece folds down across the area you need to be in. There are 2 screws to undo this part. Push it back and there is a cap that unscrews which holds the wires and socket he is talking about. Unscrew the cap, unscrew the wire and housing. The bulb comes out. You pull the wire harness off and install the new bulb. It has a triangular push-in and it has to go just right so take note of how it comes out. Also, being a halogen light bulb, do not touch the bulb with your hands - the oils will make it explode.
Posted on Apr 06, 2009
This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.
Posted on May 22, 2009
it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,
Posted on Oct 05, 2009
Tips for a great answer:
Aug 17, 2014 | 2002 Hyundai Santa Fe
on Oct 24, 2013 | Hyundai Cars & Trucks
Jul 28, 2014 | 2004 Hyundai Santa Fe
Sep 24, 2011 | 2001 Hyundai Santa Fe
Dec 02, 2010 | 2002 Hyundai Santa Fe
Mar 29, 2010 | 2003 Hyundai Santa Fe
Mar 23, 2010 | 2002 Hyundai Santa Fe
151 people viewed this question
Usually answered in minutes!