Question about Dodge Dakota

1 Answer

Where is the air and heat blend motor on a 2000 dodge dakota?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 752 Answers

Hi Sharon, I'm glad to help. Your 2000 year doesn't have a motor for the temp door. It operated by a cable running from the control head to the temp door and you work it manually. If you can't control the temperature from hot to cold, sometimes the cable come off or breaks. Here how you can see the cable to see if its working. Remove the radio and right behind it you will see the cable attached to the door, while watching it move the temp lever from hot to cold and watch it. If it is moving then its most likely out of ajustment. If it is not moving, then you'll need a new cable. Just in case it is moving, I'm attaching the instruction on how to adjust it below. Hope this helps and have an awesome day Sharon!



TEMPERATURE CONTROL CABLE

Any time the heater-A/C control or the temperature control cable are removed and/or replaced, the following procedure must be performed.
  1. The temperature control cable housing and core must be installed at both the heater-A/C control and the heater-A/C housing ends, and the heater-A/C control must be installed in the instrument panel. See Heater-A/C Control and Temperature Control Cable in the Removal and Installation section of this group for the procedures.
  2. Rotate the temperature control knob on the heater-A/C control so that the knob pointer is in the 12 o'clock position.
  3. Pull the temperature control knob straight out from the heater-A/C control base until the perimeter of the knob (not the knob pointer) protrudes about 6 millimeters (0.25 inch) from the face of the control base.
  4. Rotate the temperature control knob to the 1 o'clock position. Push in on the knob slightly and continue rotating the knob to its full clockwise stop. The knob pointer should be aimed at a position about 8 millimeters (0.315 inch) beyond the end of the graduated red strobe temperature control graphic on the face of the heater-A/C control base. If the knob is not pointed to the correct position, go back to Step 2 and repeat the adjustment procedure.
  5. Rotate the temperature control knob counterclockwise until the knob pointer is in the 12 o'clock position again.
  6. Push the temperature control knob straight in towards the heater-A/C control base until the perimeter of the knob (not the knob pointer) is flush with the face of the heater-A/C control base.
  7. Rotate the knob to its full clockwise stop again. The knob pointer should be aimed at the end of the graduated red strobe temperature control graphic on the face of the heater-A/C control base. If OK, go to Step 8. If not OK, go back to Step 2.
  8. Rotate the knob to its full counterclockwise stop and release the knob. If the knob springs back from the counterclockwise stop, the self-adjuster clip that secures the temperature control cable to the blend-air door lever is improperly installed. See Temperature Control Cable in the Removal and Installation section of this group for the procedures. If the knob does not spring back, the temperature control cable adjustment is complete.

Posted on Jun 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 dodge caravan heater blowing cold air only car does not overheat


Feel the heater hoses where they go through the firewall. If they're both hot but you're not getting any heat, your blend door is not moving to mix heated air with unheated air. It could be the blend door actuator not working or the HVAC control unit not working.

Mar 31, 2017 | 2000 Dodge Caravan

1 Answer

How to fix 2000 dodge dakota air and heat blend motor?


Hi Sharon, I'm glad to help. The 2000 Dakota came with a cable operated Temperature Door and some times the door would get out of adjustment or break. You need to remove the radio so you can see the cable, then move the temperature slider on the control head while watching the cable if it doesn't move then you'll either need a new cable or its came loose somewhere. Check both ends of the cable and make sure they are attached. Hope this helps and have an awesome day Sharon.

May 14, 2014 | Dodge Dakota Cars & Trucks

1 Answer

Blend door location


I am trying to locate the ac blend door actuator on my 2000 cadillac seville sts: AC blows air on the floor only instead of the dash board ac vents. Appreciate any help

Jan 04, 2014 | 2005 Dodge Dakota

1 Answer

2000 ford f150 no heat change heater core and thermostat cold air help!!


Sounds like you may have a blend door issue in the heater box. Ford had a replacement inner box to help with the problem. The door was hinged on a plastic pivot which would break. Some also had electric motors that would strip the gears inside the unit and not move the blend door to the heat position.

Jan 12, 2013 | 2000 Dodge Caravan

1 Answer

Truck will not switch ac to heat is it the switch or something else


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Dec 22, 2012 | 1999 Dodge Dakota

1 Answer

Heat come out of one side of dash or ac nothing out of rt side is a vac module not working?


I guess if this was the 1970's or 1980's a vacuum motor could be the problem - same principle. However, on your 2002 Dodge Dakota, the HVAC system is completely electronically controlled. You most likely have either a bad actuator motor or a broken mode door or blend-air door on the passenger side.

Nov 01, 2011 | 2002 Dodge Dakota Club Cab

1 Answer

Have a 1998 dodge caravan blows cold only new thermastst flushed system new anti freeze help


Most likely the problem is a broken blend door inside the heater box or a broken adjuster cable going to the blend door, the blend door inside the heater box is responsible for heater output depending on your temp adjustment on your heater control panel, most likely the blend door is stuck in the cold position allowing cold air to come through the vents verses allowing the blower motor to blow warm air past the hot heater core to produce heat, check the temperature adjuster cable behind your heater controls and make sure its connected and not broken, lastly make sure the blend door isnt broken and operating freely.

Dec 06, 2010 | 2000 Dodge Caravan

1 Answer

Heater blower


on 90% of the dodges it the blower restors.good luck

Apr 05, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

Not getting much heat from the heater.


have u checked the heater core inlet and outlet hose's are the hot, one hot side one cool indicates a plugged up core. if that is ok u may have a stuck air temperature control blend door in the dash air distribution system, also make sure your engine reaches at least 180 deg F.

Mar 12, 2009 | 1998 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...