Question about 2005 Ford Bantam 1.3i

Open Question

I have a 2009 1.6 ford bantam and it is overheating and the heater doesnt work, where does the problem sit?

The heater inside the kar does not work at all and when i park the car i hear excessive noise caused by the fan, i just saw it this morning but heard the engine making that noise last night but the heater still worked and the bakkie did not overheat. a while back my aircon was also giving me a problem but just for one day where it would give verry hot air when temp was set to cold and aircon was on but that stopped and now couple weeks later this happens. does anyone have any advice for me? im scared now to drive the bakkie because i dont want to damage it if there is a problem.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Bloomingidoi
  • 49 Answers

SOURCE: Heater only blows hot (well, warm) on full speed of fan

Replace the temp control on this car, it should be electrical control not cables.

Posted on Dec 03, 2008

Ad
  • 141 Answers

SOURCE: heater on ford 2003 ford pick up blows cold air

on the evap box there is a control mtr that switches the hot cold door. these mtrs are prone to failure. the other problem that i have seen is that the door breakes in side the evap box and that means removing the box to replace the door . if i remeber correctly you may have to slide the dash back to gain assces to the control mtr to test it good luck

Posted on Dec 22, 2008

knotbeerdan
  • 413 Answers

SOURCE: 1995 ford windstar overheat after replacing the thermostat

Let your engine warm up with the rad. cap off and see if the coolant level drops. and make sure your overflow is full. It blows cold air because there is no water getting to the heater core. And it shows a normal(ish) temp because the water needs to be touching the temp. sensor. I really do think there is air in the system and there is not enough coolant but hard to tell from here. Also as with overheating any time make sure to check your oil and look for any coolant as the head gasket seldomly holds together if the motor overheats.

Posted on Dec 22, 2008

  • 7 Answers

SOURCE: Ford Windstar SE, 3.8L V6, 1999, front seat heat/defrost is cold

the blendor actuators strip out the gear inside the actuator cases on these all the time. replace the actuator.

Posted on Mar 19, 2009

crayzeetrayn
  • 837 Answers

SOURCE: Overheating and no hot air from heater.

Glad to be of help ... Rate me a FixYa please .. Thanks .. Crayz

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Obd does not communicate on my ford bantam rocam 2009


should do.. ford uses the obd2 diagnostic system
what brand diagnostic reader is it

the cheaper units are not that great
has been issues with faulty wiring or plug to the ecu

26223297-evitet2jl4lc3pmm5nhbf4w4-3-0.jpg

Jun 22, 2016 | Ford Cars & Trucks

1 Answer

Flush heater core on 2009 ford ranger


if your just doing the heater core you can clamp off the heater hoses to the core, disconnect them from the heater core and run water through it both ways. if its real bad connect spare hoses to the heater core spigots and pour CLR into the core until it is full(coming out other hose) block off hose so the core is filled and let sit. then flush out again until water runs clear. if this won`t clear it then it will have to be replaced.

Mar 06, 2015 | 2009 Ford Ranger Regular

1 Answer

How do I replace a timing belt on a Bantam 1.6i XLT


if it rocam engine it does not have a belt it runs on a chain

Aug 20, 2014 | 2008 Ford Bantam 1.6i

1 Answer

Fuse box layout for ford bantam


On this website (link below) you find fuse box diagram and description for Ford Bantam

Ford Bantam 2002 fuse box diagram Auto Genius

May 16, 2014 | 2006 Ford Bantam 1.3i

1 Answer

Hissing noise from reservoir on ford bantam 2009 1.6i


air in the system .put your heating on full .to bleed the heater.remove the expansion bottle cap .run the engine push in the hose from your radiator with your fingers to get the air out your bottle and replace your cap.

Dec 18, 2013 | 2005 Ford Bantam 1.3i

2 Answers

Cadillac CTS overheating while sitting still


Hi,It sounds as though the radiator is blocked.the heater might be opening letting in hot air which will over ride the cool air.

May 24, 2013 | Cadillac Cars & Trucks

2 Answers

Guys I've got a problem with a ford bantam 1.6i 2003 model rocam engine, its overheating even though the cylinder head was skim but it still overheating. please assist!


Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

Jan 07, 2013 | 2006 Ford Bantam 1.6i

4 Answers

Ford bantam rocam 1.6i speedo,temperature gauge and rev counter not working


Sometimes when the batery of vehicle goes flat or when u fit a new car batery to the bantams they love to give that problems like gauges not working rpm not working speedo not working and cluster display is dead, u disconect the batery termanils and for example fit positive termanil and arc. Or short til that blue spark occur then u swop around negative on and arc positive,leave the ignition switched on arc til gauges move!! Don't ask me why but that happend to me! A autoelek friend of mine showed me this! NB don't tri this with vehicles with a lot of elektric featers it can cause demage to ecu (engine control unit)

Feb 19, 2012 | 2008 Ford Bantam 1.6i

Not finding what you are looking for?
2005 Ford Bantam 1.3i Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...