Question about Hyundai Accent

Open Question

How do i set the security code for my accent after a flat battery

How do i turn the radio off? and how do i enter a code number highter than 6 etc

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Z3 2001 Radio

TURN ON THE IGNITION FOR APPROXIMATELY 2 HOURS AND CODE WAIT WILL DISAPEAR AND YOU WILL GET:

CODE_ _ _ _ _ _

Posted on Aug 02, 2008

  • 1 Answer

SOURCE: I need to reset my

This will fix it. I just did mine. You do NOT need to pull out your stero to get the Serial Number.

If you lost the code, you may retrieve it from https://radio-navicode.honda.com/

Posted on Nov 08, 2008

  • 3 Answers

SOURCE: Radio code won't work

Yes I've had the same problem you need to switch off the Radio and disconnect the battery again - Leave battery disconnected for about 5 mins and reconnect. then switch on the radio and you should have code displayed. Then type your code number in and away you go.

Posted on Nov 19, 2008

johnny5846
  • 379 Answers

SOURCE: re setting the radio on my VW Golf

heres what u do , switch radio on , safe appears in radio display , followed by 1000 approximately 3 seconds later , input the security code found on the radio card using the station preset buttons on the radio , Button 1 corresponds to the first number in the security code , 2 is the second and so on . press the applicable button repeatedly until the desired number appears in the display , ( press button 1 three times if the first number is 3 ), when the entire code has been input and appears on the display , press the right side of the seek button for longer than 2 seconds until an audible signal is heard , ,,, if you do not get this procedure correct , in 2 attempts , the radio will lock up for 1 hour before you can try again .. if this happens , leave the radio on for minimum 1 hour without touching it , after that time you may try again ..

J5

Posted on Jan 15, 2009

  • 34 Answers

SOURCE: Changed battery in 2004 VW Passat - radio is completely dead

there is another fuse at the back of the radio. if that fuse is ok check if there is power comeing to the radio if there is u will need a new radio

Posted on May 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to get my radio to work after the battery went flat?


You have to enter the security code which should be with the paperwork that came with the car. If you don't have that, take your title and driver's license to the dealer and for a small (sometimes) fee they will give you the code.

Mar 25, 2016 | Cars & Trucks

1 Answer

My battery died and was replaced by the NRMA. Now my stereo system does not work. What do I do?


Good old Hyundai. You have to fire up stereo by entering the 'radio p.i.n. code' Nearly all manufacturers keep a database of p.i.n.nos per chassis number, but not Hyundai, if your radio shuts down,and you don't have a Radio Security Card (with the p.i.n.on it) then the set must be removed, model code and serial numbers recorded and then you contact the dealer (service division) with these numbers AND the cars VIN/Chassis number - they ay then supply you with the p.i.n, usually with a fee attached. In doubt, let dealer remove radio.

Oct 31, 2010 | 1996 Hyundai Accent

1 Answer

The battery went dead in my 1999 Monte Carlo and the radio is saying lock. What can i do?


here is what u must do.

GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
the
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
you're
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
you
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
you
for the 6 digit code that you've written down. Enter that and press
the
* key. He will then give you a code, and the option to get additional
4
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
until
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
the
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
and
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
receive
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
does work.

Sep 15, 2010 | 1999 Chevrolet Monte Carlo

2 Answers

Cant tune radio


Radio probably requires an unlock code, this is an annoying security feature to deture would be thieves from stealing your radio. Once power is lost to the raido it needs to be reactivated by entering a code. The original code would have been found in the manual that came with the vehicle, but you could probably find it online with the right info, car make, year, radio S/N number etc. Good luck

Feb 04, 2010 | 2000 Hyundai Accent

1 Answer

2000 chevy silverado z71.DISCONNECTED BATTERY CABLE AND NOW RADIO IS LOCKED.PRESSED 2-3 AND RECEIVED -122,THEN PRESSED AM-FM AND RECEIVED 121.


GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
the
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
you're
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
you
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
you
for the 6 digit code that you've written down. Enter that and press
the
* key. He will then give you a code, and the option to get additional
4
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
until
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
the
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
and
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
receive
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
does work.

Dec 26, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

I have a 2001 S10 chevy, and my radio went on security lock when the battery was discconected and now cannot unlock, would anyone have the pin to unlock it.


GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
the
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
you're
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
you
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
you
for the 6 digit code that you've written down. Enter that and press
the
* key. He will then give you a code, and the option to get additional
4
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
until
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
the
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
and
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
receive
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
does work.

Dec 20, 2009 | 2001 Chevrolet S-10

3 Answers

Left key on, battery died..now stereo won't work...says something about a code?


Modern stereos have an inbuilt security code which is there to prevent theft and damage to your car.. If you remove the continuous supply from the radio ( by any means which includes a discharged battery) then the radio will not function until the correct security code has been entered. BE WARNED, some radios will only give you a limited number of attempts at entering this code. If you use up those attempts then the radio will be permanently disabled and may have to be returned to its manufacturer to have the code cleared, this can be very expensive. Check your vehicle documentation to see if the code is given, it may be on a small card ( like a paper credit card) and the manual for the radio will tell you how to enter the code. Follow the manual to enter the code and if you do everything correctly, the radio will spring to life. If you do not have the code, take the vehicle and all your ownership documents and your own ID to the dealership as they will need proof of ownership and your ID to give you the code. Some dealerships will only post the code to you so be prepared for a wait. There is no method of circumventing this security so get the correct code and follow the manual for entering it..

Nov 09, 2009 | Acura TL Cars & Trucks

2 Answers

Radio


GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
the
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
you're
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
you
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
you
for the 6 digit code that you've written down. Enter that and press
the
* key. He will then give you a code, and the option to get additional
4
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
until
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
the
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
and
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
receive
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
does work.

Sep 16, 2008 | 1997 Oldsmobile Achieva

1 Answer

I have a hyundai sonata classic 2000 model disconnected the battery lead to clean them, now the radio will not work I have a security code but not sure how I put it in to radio


Once you turn on the unit, "1 CDE" will appear on the LCD. Then using preset button 1~4 enter the 4 digit security number supplied on security card. After confirming the number, press preset button 5. This should unlock the player. If the incorrect code is entered "2 CDE" will appear on LCD and if incorrect code is entered again, "3 CDE" will appear on LCD. If, after the third attempt, the code is incorrect, the set will turn off. Wait 1 hour before re entering a security code.

Aug 26, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...