Question about 1999 Chrysler Concorde

Open Question

How find Egr valve 3.2l concorde - 1999 Chrysler Concorde

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: how do you replace the egr valve in a 1997

Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing

  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Posted on Sep 04, 2009

Ad
Ironfist109
  • 3018 Answers

SOURCE: Need to replace egr valve on 2000 chrysler




  1. Make sure the fuel tank is 5/8 capacity or less before replacing or a fuel spill could result.
  2. Disconnect negative battery cable.
  3. Remove the rear lower seat cushion.
  4. Push seat back and up to remove seat cushion.
  5. Fold back the foam pad covering access cover for modules.
  6. Remove plastic access covers from floor pan right side.
  7. Disconnect the fuel supply line from module.
  8. Mark the module orientation.
  9. Drain fuel from right side of fuel tank. Lift module up enough to push hose into tank and drain. Do not spill fuel in interior of vehicle.
  10. Pull module up and out of fuel tank.
  11. Fuel Pressure regulator location.
  12. Note location of ground wire tab location.
  13. Remove ground wire.
  14. Use a screwdriver and pry up on retaining clip.
  15. Clip in the off position.
  16. Fuel pressure regulator removed.
  17. Remove O-ring from module.
  • Reverse to install making sure to use all new O rings and clips and check for leaks post repair.



ironfist109_397.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony



Posted on Oct 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced egr valve after code p0406 and still getting code and stalling and spitter sputtering when it occurs , but it only happens once car gets hot at certain temp


The code problem is related to the EGR valve but not necessarily the valve itself. There is a high input in valve position sensor that can be the sensor ---wiring short to positive and ECM. Check the connections for moisture and are not shorting out. Check that the wiring is not touching any hot parts of the motor and has burnt through

Aug 24, 2013 | 2000 Chrysler Concorde

1 Answer

Po404 check engine code


Code 404 is a problem with the EGR position sensor.
The valve and sensor would need to be tested.

Jan 18, 2013 | 2001 Chrysler Concorde

2 Answers

What is a EGR valve & IAC valve & where are they located?


Here's a picture of your egr valve,located by firewall.Here's your iac.

Jan 17, 2013 | 2000 Chrysler Concorde

1 Answer

Just want to make sure b4 i tear into it tomarrow..that the egr is mounted on the passenger rear side of the motor. 2001 chrysler concorde 3.2



  • It's on the backside of the right head. To gain access to the EGR you will need to remove the airbox.. Then just a couple 8mm bolts to remove the vacuum hose off the EGR. The remove the two 13mm bolts that mount the EGR (from the back of the head). See diagram below.


ironfist109_443.jpg




  • Hope this helps.

Nov 01, 2011 | 2001 Chrysler Concorde

2 Answers

Need to replace egr valve on 2000 chrysler concorde





  1. Make sure the fuel tank is 5/8 capacity or less before replacing or a fuel spill could result.
  2. Disconnect negative battery cable.
  3. Remove the rear lower seat cushion.
  4. Push seat back and up to remove seat cushion.
  5. Fold back the foam pad covering access cover for modules.
  6. Remove plastic access covers from floor pan right side.
  7. Disconnect the fuel supply line from module.
  8. Mark the module orientation.
  9. Drain fuel from right side of fuel tank. Lift module up enough to push hose into tank and drain. Do not spill fuel in interior of vehicle.
  10. Pull module up and out of fuel tank.
  11. Fuel Pressure regulator location.
  12. Note location of ground wire tab location.
  13. Remove ground wire.
  14. Use a screwdriver and pry up on retaining clip.
  15. Clip in the off position.
  16. Fuel pressure regulator removed.
  17. Remove O-ring from module.
  • Reverse to install making sure to use all new O rings and clips and check for leaks post repair.



ironfist109_397.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony



Oct 13, 2011 | 2000 Chrysler Concorde

1 Answer

2.7 2000 concorde still running funny after putting new crankshaft and cam sensors on it.Idles funny and engine seems to hesitate for a second when accelerating.Almost like engine cuts out for a...


Sounds like the timing belts needs to be replaced and it is a real pain on those cars best to do the water pump also. I suggest a really good mechanic do the work though. It took me about 8 labor hours to do this.

Jun 19, 2011 | 2000 Chrysler Concorde

2 Answers

Engine error lite P0465


Replacing the EGR valve, its actuator, or your DPFE sensor could all be at fault. I would probably start with the valve itself since it's an EGR leak code. Your gas cap was a wasted repair. The gas cap would cause a P0441 or 445 evap code, but not an EGR code.

Oct 07, 2009 | 2000 Chrysler Concorde

1 Answer

How do you replace the egr valve in a 1997 chrysler concorde lx


Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing
  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Sep 04, 2009 | 1997 Chrysler Concorde

1 Answer

Rough idle and check engine light concord


Check your EGR valve and your IAC Idle Air Control valve make sure both are functioning correctly

Feb 15, 2009 | 1997 Chrysler Concorde

Not finding what you are looking for?
1999 Chrysler Concorde Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...