Question about 1983 Chrysler LeBaron

Open Question

91 Chrysler LeBaron Convertable top stuck down

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 80 Answers

SOURCE: 1982 Chrysler LeBaron Convertable

What happened on mine was the motor failed.Check behind he rear sear at the motor to see if you have voltage. I was't willing to replace the motor for 300 bucks so i disconnected the rod ends that push and pull the top and made it a manual top.Works fast and not too hard.

Posted on Jan 26, 2009

Ad
  • 50 Answers

SOURCE: 2000 chrysler sebring convertable top will go down but will not

Typically, when when this happens, the system is low on fluid and/or must be bled. Here are the procedures:
Lower the top to the full down position.

  1. Remove the rear seat cushion, seat back and inner quarter trim panels. Pull up sharply on the seat cushion at the front about midway between the middle of the seat and the outside edges. The seat back is held in by nuts. The quarter trim panels are held in by screws I think.
  2. Remove the cylinder mounting brackets and remove the cylinders from the trunnion pivot mounts.
  3. Rotate the cylinders 180 degrees (the hose fittings will now face to front of the vehicle.
  4. Disconnect the motor/pump retaining clips from the body.
  5. Rotate and raise the motor/pump assembly so the reservoir is in the up position. The rubber filler plug will be at the top.
  6. Raise motor/pump fitting to at least 2 inches above the horizontal rear seat back reinforcement.
  7. Tilt the motor/pump assembly to approximately the 10 o'clock position, with the rubber filler plug still at the top CAUTION: THE MOTOR/PUMP ASSEMBLY MUST REMAIN IN THE CURRENT POSITION UNTIL THE RUBBER FILLER PLUG IS REINSTALLED IN THE Step 12.
  8. Remove the rubber fill plug from reservoir.
  9. Fill the hydraulic system by adding Dexron 2 Automatic Transmission Fluid to the bottom of the fill hole CAUTION: DO NOT OPERATE THE TOP SWITCH IN THE UP (CLOSING THE TOP) DIRECTION.
  10. With two people, activate the top switch in the down (opening the top) position to fully retract the cylinder rods and hold for approximately 5 seconds, until the motor/pump stalls. A percolating or gurgle sound/feeling is an indication that the procedure is working.
  11. Top off the motor/pump with Dexron 2 and insert the filler plug.
  12. Install the motor/pump assembly into the vehicle mounting bracket.
  13. Rotate the cylinders back to the original position (hose fitting rearward)
  14. Install the motor/pump lead and hydraulic line clips (the hydraulic line clips are to assist in the production process) to ensure that the seat back/seat cushion do not pinch the lines. If the sticky side is no longer holding to the floor pan, the clips can be left off.
  15. Ensure that the bushing is still on the trunnion pivot mount and bracket. Tap the top switch in (raising the top) to get the cylinder trunnion onto the trunnion pivot mounts, if needed.
  16. Install cylinder mounting brackets.
  17. Raise and lower the top to ensure proper operation.
  18. Install the inner quarter panels, and the rear seat back and cushion.
  19. And Just a fair warning here - you WILL spill fluid inside your car. If you manage not to, I want to know how. I cover everything with garbage bags because there have been a few instances where I accidentally hit the button the wrong way and that stuff went EVERYWHERE. Be careful and good luck.

Posted on Apr 17, 2009

  • 93 Answers

SOURCE: Can I manually raise my Convertible top on my 1994 Chrysler Lebar

You can, but it will probably take two people and they must move the top slowly and together. It will be hard because you will be forcing the fluid back through the pump.

You can change it to a manual top by removing the bolt at the top of the cylinders and lowering the both shafts down into the cylinders.

Karl at topgunwon.com

Posted on Jan 25, 2010

arauzvictor1
  • 466 Answers

SOURCE: 91 Chrysler Lebaron tachometer, dome lights and

You have to check the fuse 26 is 15 amp as this is the one that feeds the lights and radio.Thanks good luck and I hope your opinion

Posted on Jan 29, 2010

  • 93 Answers

SOURCE: How to install a rear vinyl window in a convertible

Your window is not attached to the top material.
Both the top and the window are attached directly to the frame.
You can get instructions for this procedure on DVD at this link.
http://www.topgunwon.com/DVD/

Regards, Karl

Posted on Feb 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Convertable top will not work


Fix freeze plug on a 2003 Chrysler 300 m

Aug 19, 2013 | 1990 Chrysler LeBaron

2 Answers

Does chrysler lebaron have resevoir for the convertable top


inside the pump/? did the installer put fluid into the pump wen he installed it?

Apr 21, 2013 | 1994 Chrysler LeBaron

1 Answer

How do I remove the windshield wiper arm from a 1995 chrysler lebaron convertable?


To remove the wiper arm from a 91-94 LeBaron Convertible:
1: Remove the blade first. (Hood up was easier on mine)
2: From under the hood, lift arm high enough so you can get the small tab at the base of the arm to slide back toward the windshield about 1/4 inch. The tab won't move back until the arm is lifted enough to make clearance for the tab. With the tab moved back, it will keep the arm from coming back down if done correctly but BE CAREFUL that the blade doesn't spring down onto the windshield or put a towel down in the area to cushion any accidents!
3: With the tab now pushed back and holding the arm from returning down you can now slide (jiggle) the arm off from the shaft. It may seem still locked on but if the tab is out far enough to catch the arm from returing it is far enough and you just need to wiggle just right or maybe spray some WD-40 to help, but you really shouldn't need WD-40
Installation is reverse of these instructions.

Jun 13, 2012 | 1995 Chrysler LeBaron

1 Answer

92 lebaron convertable. When it rains, the top


If you out the top down, on the windshield side posts you will see a small drain tube on each side. When these cars age the sealant used around the drain tubes rends to get crushed and distorted and tends to cover these tubes not allowing the water to drain down the A posts. This causes the water to back up and run down the inside of the A post and under the dash and onto the floor. It's also possible that the window seals are in need of replacement or adjustment.

Jul 29, 2010 | 1992 Chrysler Lebaron

1 Answer

REAR WINDOW DRIVERS SIDE WILL ROLL DOWN BUT NOT UP ? 1989 CHRYSLER LEBARON GT 2D CONVERTABLE


The control switch is probably bad. You could try taking it apart and looking for a broken piece. You may be able to get it to work again. Otherwise, just replace the switch with one you get from a junk yard.

Oct 23, 2009 | 1989 Chrysler LeBaron

2 Answers

Back side windows will not work


could be a fuse or the motor for the window

Sep 10, 2009 | 1991 Chrysler LeBaron

1 Answer

91 lebarron wont shift grears when its in drive,


Does it act like it is stuck in 2nd? (Limp in mode) Have the TCM scanned it has trouble codes stored in it.

Apr 14, 2009 | 1991 Chrysler LeBaron

1 Answer

1982 Chrysler LeBaron Convertable


What happened on mine was the motor failed.Check behind he rear sear at the motor to see if you have voltage. I was't willing to replace the motor for 300 bucks so i disconnected the rod ends that push and pull the top and made it a manual top.Works fast and not too hard.

Aug 09, 2008 | 1983 Chrysler LeBaron

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...