Question about 1994 Jeep Grand Cherokee

Open Question

How to disconnect anti-theft module 1996 grand jeep cherokee 5.2litre v8

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: 1996 jeep grand cherokee 4 x 4 with 5.2 liter v8

under the vehicle...mounted close to the front of the fuel tank...be sure to release the fuel pressure before you disconnect any line..you can do that by removing the fuel pump relay and cranking the engine

Posted on Sep 27, 2008

  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

  • 6982 Answers

SOURCE: I need a wiring Schemattic (Diagram) for a 1996

I work mainly from memory and was a bit concerned that I was giving you the wrong color!

Glad it's OK now! Good luck

Posted on Jan 25, 2010

  • 2926 Answers

SOURCE: I need a routing diagram for my 1996 jeep grand

ledsled378_96.jpg
..................

Posted on Feb 17, 2011

ZJLimited
  • 17970 Answers

SOURCE: how do i reset the

I suggest check the procedure for antitheft system in this link: Jeep-Grad-Cherokee-Anti-Theft-System

Hope helps (remember to rate this answer).

Posted on Apr 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect anti-theft module 1996 grand jeep cherokee 5.2litre v8


so all 3 FOBs are dead? is that it??????
so the which part of the system is failing
the ASD relay cuts starts, 7 ways, one is security. called VTSS.

i guess the security light is telling you, that it is not happy? in the dash cluster, is that it?
94 or 96?
so it , flashes ext. lamps, honks horn, and wont start.
page 8q-1 FSM.

http://www.jeepforum.com/forum/f13/how-disable-your-alarm-your-zj-483020/

endless post. on topic. read it, try it.

better yet, diagnose it.
scan the PCM to find out why the ASD relay drops out
does it? that is the first test in all, no starter.
http://www.fixkick.com/Jeeps/ASD.html

if the battery is discharged, bad things happen as the security logic
goes nuts. (the chips dont yet run on "free energy" )

May 13, 2014 | 1994 Jeep Grand Cherokee

1 Answer

1996 jeep gcl and pcm is locked in theft mode. runs for 3 seconds and stops. Scanned vechicle and everything is ok but wont come off lock


Hi James:
Just keep in mind that the 1993-1998 Grand Cherokee was called "ZJ Series", so they have the same device and systems; in your 1996 Jeep Grand Cherokee Anti-Theft System is equipped with Vehicle Theft Security System (VTSS).

VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The ZL's Jeep Grand Cherokee Anti-Theft System. HERE you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding.

Additionally, Is request your email account to send this diagram (big scale) and other details in PDF format where you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer. Keep in touch.

Thank you for using FixYa, have a nice day.

Jan 31, 2012 | 1996 Jeep Grand Cherokee

1 Answer

How can I disable jeep grand cherokee security system


Hi Andrew:
The 1994 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running. I have an '93 GC 5.2L V8...

The following wiring diagram and electronics circuit contains detail schematics of The 1994 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE and also, remember that here can find the Jeep Grand Cherokee Service Repair Manual.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 25, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Jeep grand cherokee alarm system


The 1995 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The 1996 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE and also, remember that here can find the Jeep Grand Cherokee Service Repair Manual.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 25, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do you disarm factory anti-theft system on a 1993 Jeep Grand Cherokee


Nices Jeep model, I have the same year with 5.2L V8 engine; visti the next link to know details about 93ZJ-Secc-8Q-Vehicle-Theft-Security-System

Hope this helps.

May 01, 2011 | 1993 Jeep Grand Cherokee

1 Answer

1999 Grand Cherokee Limited Jeep anti-theft system had shut all electronics down and engine will not start. what can I do to reset the system....


The 1996 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The 1996 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE.

Also, remember that here can find the Jeep Grand Cherokee Service & Repair Manual.
Hope help with this.

May 03, 2010 | 1999 Jeep Grand Cherokee

2 Answers

How do you reset a anti-theft system on a 1998 jeep grand cherokee limited 5.2 v8.


You can pull the battery for 10 mins and it should reset the entire ECU PCM and Anti Theft system

Sep 01, 2009 | 1998 Jeep Cherokee

2 Answers

Alarm sets itself with doors unlocked


you can`t it is part of the body control module

Mar 16, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...