Question about 2003 Mitsubishi Eclipse Coupe

Open Question

Crankshaft sensor location

I need to know the location of the crankshaft position sensor of a 2003 Mitsubishi eclipse 4 cylinder. While riding down the highway shifting into 5th gear my car lost all voltage power and then would not start I have to replacement part I just need help now finding the sensor to replace it.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: crankshaft position sensor location

if u pull the battery and battery tray u can easily reach this

Posted on Nov 23, 2008

Big Poppa Ma
  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

bschilz
  • 2049 Answers

SOURCE: Location of thermostat 2003 Mitsubetsi Eclipse 4

The thermostat is found at the end of the top radiator hose . Find the top radiator hose and follow it to the engine .There you will find a thermostat housing with the end of the hose attached . There will be 2 bolts holding down the housing to the engine. Undo the bolts and pull the housing off and the thermostat will be there.

Posted on Sep 06, 2009

GARYca
  • 672 Answers

SOURCE: Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located in the 1990 Chevrolet Corsica 4 cylinder 2.2 liter engine?


Follow this link to a diagram that will show you where it's located. Hope this helps.

Jul 11, 2016 | Chevrolet Cars & Trucks

1 Answer

What does error codes 40 and 41 mean on my 1999 mitsubishi eclispe mean


11 Oxygen sensor fault.
12 Airflow sensor fault.
13 Intake air temp sensor fault.
14 Throttle position sensor (TPS) fault.
15 Idle speed control (ISC) motor position sensor fault.
21 Coolant temp sensor fault.
22 Crankshaft position (CKP) sesnor fault.
23 Camshaft position (CMP) sensor fault.
24 Vehicle speed sensor (VSS) fault.
25 Barometric (BARO) pressure sensor fault.
31 Knock sensor fault.
32 MAP sensor faulty.
36 Ignition timing adjustment signal fault.
39 Oxygen (O2) sensor fault.
41 Injector(s) fault
42 Fuel pump fault.
43 EGR fault.
44 Ignition coil (cylinders #1 & #4) fault.
52 Ignition coil (cylinders #2 & #5) fault.
53 Ignition coil (cylinders #3 & #6) fault.
55 Idle air control (IAC) valve position sensor fault.
59 Rear Oxygen (O2) sesnor fault.
61 Transaxle control module torque reduction signal fault.
62 Variable Induction control (VIC) valve position sensor fault.
71 Traction control (TC) vacuum valve solenoid fault.
72 Traction Control (TC) vent valve solenoid fault.

Sep 26, 2014 | 1999 Mitsubishi Eclipse

1 Answer

Crankshaft position sensor location


Look on the transmission bell housing

Dec 21, 2013 | 1995 Mitsubishi Eclipse

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

1 Answer

My 1997 Mitsubishi Eclipse wont pass emissions because trouble code P1390. I dont know what this means? Ive researched it everyway I know? My check engine light wont come on at all? Help anyone? Thanks!


This is the direct definition of this code
Mitsubishi DTC P1390 - Timing Belt Skipped 1 Tooth or More.
Probable Causes,
-Timing belt improperly installed
-Camshaft position sensor improperly installed
-Camshaft position sensor connector improperly connected
-Crankshaft position sensor connector improperly connected
-Camshaft's relative position not relearned after one of the following have been serviced: Camshaft, Camshaft sprocket, timing belt tension-er, cylinder head, head gasket, crankshaft sprocket, crankshaft cylinder block or the PCM.

Sounds like something to do with the timing belt it self. You can go to any Autozone or Checker and ask for a code reader (they will let you use it for free) and it will show this code again. You can also reset the cars computer with the code reader to see if it comes back with the same code.

Nov 03, 2010 | 1997 Mitsubishi Eclipse

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Where is bank1 sensor 1 (O2 sensor) of 2003 Mitsubishi Eclipse


if its a 4 cylinder it will the 02 sensor closest or if not in the exhaust manifold

Aug 05, 2009 | 2000 Mitsubishi Eclipse

1 Answer

2002 Eclipse


its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Dec 06, 2008 | 2002 Mitsubishi Eclipse

2 Answers

Crankshaft position sensor location


under hood, center, upper engine area, mounted on upper driver side of engine.

Nov 21, 2008 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...