Question about 2004 Chevrolet Malibu

Open Question

Replace hazard lite switch 2004 chevy classic malibu

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 chevy malibu classic

Happens all the time to me. I trigger the Theft System by accident then the car won't start.  try this: Put the key in the ignition. Turn it to the "on" setting,but don't try to start the engine. Let it sit for 10 minutes until the Security light stops blinking and turns off. Take the key out and restart. Warning - don't have your lights, radio,etc on while you do this or the battery may die. 

Posted on Jun 02, 2008

  • 1 Answer

SOURCE: 2004 chevy malibu classic spark plug replacement

Search for the engine model ECOTec 2.2 rather then Malibu. It is very easy to replace the plugs, they are DEEP inside the engine so you will need a 6" socket extension for the spark plug socket. Needle nose pliers were required to retrieve the socket on the first plug. Don't push down hard on the plug, just enough to engage the nut. Full screen photo sequence is available at:
http://www.gaownersclub.com/forum/showthread.php?t=99068

Posted on Aug 09, 2009

  • 3640 Answers

SOURCE: 2004 Chevy Malibu Classic and problem is turn signal goes out

the hazzard switch is together with the turn signals, so if they are not working properly, check hazzard switch. the switch has a built in timer for hazzards and turn signals.

Posted on Oct 01, 2009

lasvegasrich
  • 65 Answers

SOURCE: replacing spark plugs on a 2004 chevy malibu

2.2L Engine

  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Posted on Oct 07, 2009

Testimonial: "Thanks for the help, it was easy to change out the plugs with your info."

techbuster
  • 5081 Answers

SOURCE: How do I replace a headlight bulb for a 2004 chevy

Change headlights in 2004 Chevy Malibu Classic
Open the hood and pull up on the two black tabs on either side of the lamp assembly. Pull the lamp assembly forward gently and unclip the wiring harness. Twist the socket counter-clockwise and remove it. The bulb should be removed by wiggling it.
Install new bulb in its place and turn the socket back into place. Reconnect the wiring harness and return the lamp to its original position. Line up the holes in the lamp assembly to the round ends of the mounting pins, and press down on the two black tabs to hook the lamp assembly into place.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the brake light switch in a 04 chevy malibu classic?


There is either a clip or a nut holding it to the bracing under the dash against the upper part of the brake pedal. Unplug the connector and swap out the switch. Its relatively easy.

Jan 29, 2011 | 2004 Chevrolet Malibu

1 Answer

Where is the turnsingle flasher located on 2004


Technically --you dont have a flasher.....The 4 way button on the dash is a combination turn/ hazard flasher control "MODULE"...

This is a common problem with these switches. I have replaced several of them over the last few months. The switch can be replaced without all of the disassembly that is recommended. I have done it. There is a screw holding the switch into the dash behind the bezels, but it is possible that it can be done without spending hours on it. The Grand Am/Prix cars were all the same, just a slightly different design.

Hope this helps.

Apr 28, 2010 | 2004 Chevrolet Malibu

3 Answers

2004 Chevy Malibu Classic and my problem is the turn signal


i have that problem also but what i do is i have to hold the hazard button and then my blinker will work i think it may be a short or something. but just try to wiggle the hazard button and see what happens

Mar 19, 2010 | 2004 Chevrolet Malibu

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

How do I replace a headlight bulb for a 2004 chevy malibu classic?


Change headlights in 2004 Chevy Malibu Classic
Open the hood and pull up on the two black tabs on either side of the lamp assembly. Pull the lamp assembly forward gently and unclip the wiring harness. Twist the socket counter-clockwise and remove it. The bulb should be removed by wiggling it.
Install new bulb in its place and turn the socket back into place. Reconnect the wiring harness and return the lamp to its original position. Line up the holes in the lamp assembly to the round ends of the mounting pins, and press down on the two black tabs to hook the lamp assembly into place.

Nov 22, 2009 | 2004 Chevrolet Malibu

3 Answers

2004 Chevy Malibu Classic and problem is turn signal goes out


the hazzard switch is together with the turn signals, so if they are not working properly, check hazzard switch. the switch has a built in timer for hazzards and turn signals.

Oct 01, 2009 | 2004 Chevrolet Malibu

2 Answers

Looking for hazzard switch for 2004 chevy malibu classic


It has a triangle on it and its in the middle of the dash panel.

Sep 06, 2009 | 2004 Chevrolet Malibu

Not finding what you are looking for?
2004 Chevrolet Malibu Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...