Question about 2006 Cadillac STS

Open Question

How to remove rear bumper cover for a hyundai veloster turbo

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2013 Hyundai veloster Turbo. I got gas 17 miles from my house. My husband went out, went on hiway, car lost power, bucked & "run rough". I tried to drive it and check engine light flashes.


you screw the cap on and the cover is what clicks in place
if it will not click in place , probably because the cap is not fully screwed down
have the fault codes read

Nov 20, 2017 | Hyundai Cars & Trucks

1 Answer

Wiper fuse keeps blowing, car 2 months old, 2014 veloster turbo


Return to the dealer for warranty! You may have a hidden recall issue, or a potential electrical fire issue.

Apr 27, 2015 | 2014 Hyundai Veloster

1 Answer

How do i reset the oil change light on my 2013 veloster turbo


I know for a lot a vehicle you put your key on all light came on then press three time the accelerator after start your engine and check it out this procedure work's for a lot of manufacturing.

Sep 13, 2014 | 2013 Hyundai Veloster

1 Answer

Hyundai veracruz front bumper


Its fitted by screws and held by assembly.Give proper support to lower side and loosen the screws and bumper should easily come off.
---------------For complete step by step details,go through the help links mentioned below :-----

How to Attach the front bumper cover to the fender on 2010 Ford Explorer?

http://technoanswers.blogspot.com/2012/01/how-to-attach-front-bumper-cover-to.html
-----------

How to replace Bumpers on Acura Car models?
http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-bumpers-on-acura-car.html
-----------

How to Replace Front Bumper on Audi A4 and VW Passat?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-front-bumper-on-audi-a4.html
----------These will help.Thanks.

Nov 28, 2012 | 2008 Hyundai Veracruz

1 Answer

How do I remove the rear bumper on a 2003 hyundai sonata


You have to remove four screws near the center of the rear bumper that are visible when you open the trunk. Then remove the inside upholstery cover for each rear tail light and then remove the four brass bolts that hold each rear tail light assembly. Unhook the wiring harness so the tail light assembly can be removed and laid aside. Then remove the two screws on each side which were covered by the bottom of the tail lights. Next, remove some of the upholestry retaining pins close to the rear tailights so you can access the spcae behind them. You need to remove two brass nuts close to the outer aspect of where the tailights are located and two screws that are located several inches farther forward that are holding the more frontal aspect of the rear bumper on each side. Finally, remove two retaining screws at the bottom of the most forward aspect of the bumper (wheel well) and one at the top of the most forward aspect of the bumper and you should now be able to remove it! Hope this helps! John in Lexington

Jul 20, 2012 | Hyundai Sonata Cars & Trucks

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

Not finding what you are looking for?
2006 Cadillac STS Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...