Question about 2004 Honda Civic

Open Question

Obd code p1453 se

Honda civic 2004 is that a evap system or

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

95zcvtecsi
  • 26 Answers

SOURCE: 1995 honda civic dx

Look on the wiring harness it plugs in on top of the transmission
make sure all the wires are together. If every thing is ok with the wiring, The sensor is the only thing it could be. A gook used spedometer sensor from the junk yard will work this sensor dosent take a lot of abuse so a good used one will be cheap and work just fine. This is a job you can do your self and save a lot of money. I had the same problem with my 95 civic

Posted on Jul 21, 2008

SOURCE: what is the code?

Most hondas have the code on the vehicle itself for resetting the code once the battery has been disconected or radio removed. Try pulling the glove box out and looking on the inside of the cavity. You should not need a code to remove the radio the alarm should not go off, it is the installation. The radio will not work with any other --vehicle without your specific code, good thieves know this and would rather steal the whole car. "Especially the Honda Accord. Have one in the garage and a 2005 Pilot.

Posted on Jan 06, 2009

  • 521 Answers

SOURCE: I have a Honda 2004 CRV - the repair ( OBD II)

P2647 VTEC Oil Pressure Switch Circuit High Voltage - With Automatic Transmission Basicallly the sensor has gone bad or an oil passage has become blocked.

**. Locate the Variable Timing Electronic Control (VTEC) pressure switch on the end of the cylinder head. Honda has had problems with the VTEC oil pressure switch, there is an updated part number for the vehicle (37250-PNE-G01). On this vehicle the VTEC oil pressure switch can fail at any RPM.
2. The VTEC oil switch is normally closed, and grounds the reference voltage from the Engine Control Module (ECM) on the Blue/Black (BLU/BLK) wire. If the code sets at idle - 2500 RPM - and the Brown/Yellow wire has a good ground, then suspect a faulty VTEC oil pressure switch.
3. At approximately 2500-4000 RPM and when driving the vehicle, the VTEC system should turn on. To turn on the system, the ECM energizes the VTEC Solenoid valve and it allows oil pressure into the intake valve rocker arms, the oil pressure opens the VTEC oil pressure switch so the Engine Control Module (ECM) can verify that the VTEC did turn on correctly.
4. The code will set at idle to 2500 RPM if the reference voltage is not grounded. The code will set above 2500-4000 RPM if the VTEC oil switch does not open.
5. If the code sets at 2500-4000 RPM or higher, the problem can be a low oil level or pressure, or a malfunction in the VTEC assembly.
Potential Causes: Low Engine Oil
Plugged Oil Passage
Insufficient Oil Pressure
Plugged Oil Screen
Insufficient Oil Volume
Malfunctioning VTEC Oil Pressure Switch
Defective VTEC Solenoid

Posted on Jul 25, 2009

  • 178 Answers

SOURCE: i have a 2000 honda

right off all data

p1399 is a random misfire code and honda has reported for various models that this could be caused by clogged egr ports, in addition there is the possibility that the valve clearance spec may be out of range.check plugs and wires first and proper gap.

Posted on Aug 09, 2011

emissionwiz
  • 75117 Answers

SOURCE: where is obd II port in 2003 honda civic

It is under the dash on the drivers side, get under there and look, you will see it. Here is a picture of a typical OBD 2 connector plug.
1_23_2012_10_20_02_pm.gif

Posted on Jan 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTC P0449?


P0449 - OBD-Codes.com

www.obd-codes.com/p0449
Detailed information on diagnosing and repairing a P0449 DTC code which refers ...P0449 Evaporative Emission Control System Vent Valve/Solenoid Circuit ... OBD-IITrouble Code Technical Description ... 2004 Chevrolet Tahoe 4.8L p0449

EVAP Code P0449 - YouTube

? 16:47
https://www.youtube.com/watch?v=AlfOSMmisPg
Mar 13, 2013 - Uploaded by realfixesrealfast
Here is a description and how to diagnose EVAP code P0449. ...Up next. Quick Easy Fix P0449 P0455 Evap Codes on ChevySilverado 2007 ...

Quick Easy Fix P0449 P0455 Evap Codes on Chevy ...

? 7:06
https://www.youtube.com/watch?v=aL5KmV1d26Y
Dec 27, 2013 - Uploaded by wagslick
Quick Easy Fix P0449 P0455 Evap Codes on Chevy Silverado 2007 .... Well clearing the error codes at auto store will not prevent it come ...

Solving a P0449 Engine Code on a 2008 Chevy Impala ...

pressanykey.simplyahobby.com/.../solving-a-p0449-engine-code-on-a-2...

Jan 07, 2016 | 2004 Chevrolet Chevrolet Impala

1 Answer

What does fault code P1450 mean for Honda Cr-v ?


No P1450 on a Honda?

P1382 Cylinder Position Sensor No Signal P1456 EVAP Emission Control System Leak Detected (Fuel Tank System) P1457 EVAP Emission Control System Leak Detected (Control Canister System) P1459 EVAP Emission Purge Flow Switch Malfunction P1486 Thermostat Range/Performance Problem P1491 EGR Valve Lift Insufficient Detected P1498 EGR Valve Lift Sensor High Voltage

http://www.obd-codes.com/trouble_codes/honda

Dec 30, 2015 | Honda Cars & Trucks

1 Answer

1996 HONDA CIVIC P0450 EVAPORATE SYSTEM PRESSURE SENSOR,WHAT IS THE REASON OF THIS CODE,THE CIVIC DOESN'T HAVE FTP SENSOR.EMISION SYSTEM


The EVAP (Evaporative Emissions) System allows fuel tank vapors to be purged into the engine and burnt rather than expelled into the atmosphere as harmful emissions. The EVAP system contains a pressure sensor to check the integrity of the system. Periodically, the EVAP system performs a pressure test to check that there are no leaks in the system. It uses this sensor, also known as a fuel tank pressure (FTP) sensor to check for leaks. Basically P0453 means the PCM (Powertrain Control Module) noticed the EVAP Pressure sensor or FTP is indicating a higher than normal pressure (above 4.5 Volts) in the EVAP system. NOTE: On some vehicles the FTP is a part of the fuel pump assembly in the tank. Potential Symptoms There will likely be no noticeable symptoms along with this code other than the MIL (Malfunction Indicator Lamp), commonly known as Check Engine Light illumination. However, there may be noticeable fuel odors in some cases. Causes A P0453 DTC trouble code may be caused by one or more of the following: Open on FTP sensor signal wire Short to voltage on FTP sensor signal wire Bad FTP sensor Abnormally high pressure in fuel tank due to blockage in EVAP purge hoses or overfilled tank Loose/damaged FTP sensor connector Loss of ground to the sensor Possible Solutions Using an scan tool access FTP sensor value with Key on Engine off (KOEO). Normal value is usually somewhere near 2.5 Volts at atmospheric pressure (may fluctuate some due to altitude). It shouldn't ever be above 4.5 Volts. 1) If it is close to 2.7V with the gas cap off, the problem is likely intermittent. Using a Digital Volt Ohm Meter, measure the voltage on the signal wire while trying to induce the problem by wiggle testing all the wiring at the FTP sensor. If the voltage fluctuates when wiggle testing, check for connector problems; i.e. water in the connector, broken or chafed wiring. 2) If the value shown on the scan tool is above 4.5V, unplug the sensor (if possible) and check for voltage again. If the high voltage is still present when unplugged, inspect wiring harness for a short to voltage on the signal wire. If the high voltage disappears when unplugging the sensor, check for a good ground to the sensor and proper reference voltage. If you have a good ground and 5 Volts reference voltage, replace the FTP sensor since it's likely shorted out. Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0444 - P0445 - P0446 - P0447 - P0448 - P0449 - P0452 - P0455 - P0456

Read more at: http://www.obd-codes.com/p0453
Copyright © OBD-Codes.com

May 29, 2015 | 1996 Honda Civic

1 Answer

I have a 98 Honda Accord with the following codes P0171, P0401, P1457


Hello there
follow these links for a bit pf help

For P0171
http://www.obd-codes.com/p0171

For P0401
http://www.obd-codes.com/p0401

For P1457
P1457 EVAP Emission Control System Leak Detected (Control Canister System)

Sep 19, 2014 | 1998 Honda Accord

1 Answer

Obd code p1453 se


p1453 refers to evaporative emission (EVAP) pressure sensor, in fuel tank--signal too high when depressurised===causes--wiring--EVAP canister purge valve--hoses--EVAP pressure sensor.

Aug 01, 2014 | 2004 Saab 9-3

1 Answer

Dtc p1457,0107


P1457 HONDA - Evaporative Emissions Control System Leakage EVAP Canister Systemxicon.jpghttp://engine-codes.com/p1457_honda.htmlForum CodePossible causes- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap There is a Honda factory service bulletin with information on how to diagnose the P1456 on the following Honda models:
1998 Honda Accord
1999 Honda Accord
2000 Honda Accord
1998-2000 Honda Accord
symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vaporsP1457 HONDA Description The evaporative emission (EVAP) control system stores fuel vapor from the fuel tank in the EVAP canister temporarily to prevent it from escaping to the atmosphere and to enable it to be drawn into the engine by intake manifold vacuum and burned. In addition, the onboard refueling vapor recovery system (ORVR) stores fuel vapor generated when refueling in the EVAP canister.

The EVAP control system leak detection method improves the accuracy and frequency of the detection by determining faulty components and vapor leakage for each part. The EVAP control system (from the purge valve to the fuel tank) is divided into two parts. One is the "EVAP Canister Side" (from the EVAP two way valve to the purge valve) and the other is the "Tank Side" (from the EVAP two way valve to the fuel tank). There is 0.04 inch leak detection and 0.02 inch leak detection. If the 0.04 inch leak detection results are OK, the 0.02 inch leak detection runs. The P1457 code is detected when the EVAP system has a very small leak.

P0107 HONDA - Manifold Absolute Pressure Sensor Circuit Low Voltagexicon.jpghttp://engine-codes.com/p0107_honda.htmlForum CodePossible causes- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor poor electrical circuit connector
- Faulty Manifold Absolute Pressure sensor
- Faulty Engine Control Module (ECM) When is the code detected?An excessively low voltage from the sensor is sent to ECMSymptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Engine rough idle
- Engine hesitation
P0107 HONDA Description The Manifold Absolute Pressure sensor provides instantaneous manifold pressure information to the engine's Engine Control Module. The data is used to calculate air density and determine the engine's air mass flow rate, which in turn determines the required fuel metering for optimum combustion. A fuel-injected engine may alternately use a Mass Air Flow sensor to detect the intake airflow. A typical configuration employs one or the other, but seldom both.


In some vehicles the absolute pressure sensor is built into ECM. HONDA Technical Service Bulletins for P0107 code1999 HONDA ODYSSEY Electrical System 2000 HONDA ODYSSEY Electrical System1998 HONDA ACCORD Electrical System 1999 HONDA ACCORD Electrical System 2000 HONDA ACCORD Electrical System 2001 HONDA ACCORD Electrical System 2002 HONDA ACCORD Electrical System 1996 HONDA CIVIC Electrical System 1997 HONDA CIVIC Electrical System 1998 HONDA CIVIC Electrical System

Jul 25, 2012 | Honda Civic Cars & Trucks

2 Answers

Honda po497


The dealer has the problem that is prominent with this code you will have to referee to code P1457 they are plaque with this P0497 is evap slow leak P1457 is Evap slow leak it TSB 08-016 cansmo_128.gif

Aug 28, 2011 | 2005 Honda Accord

1 Answer

P1600


The P1600 is a generic OBD II code. It just means that a more specific code (Honda) has been set. To find the specific code you have to take it to the dealer or have a Vetronics Mastertech scan tool to get the actual code. The P1433 indicates thats the the main battery contactor or the by-pass contactor is staying active when it should not. Using an Actron pocket code reader will only read generic OBD II codes. Hope this helps.

Oct 17, 2010 | 2004 Honda Civic

Not finding what you are looking for?
2004 Honda Civic Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...