Question about 1998 Jeep Wrangler

1 Answer

1998 wanger high idie - 1998 Jeep Wrangler

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Probably the idle air valve on the passenger side of the throttle body. It's about a $40 part and simple to replace.

Posted on Jun 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What diesel engine was used in the 1989 ford chassis ford


For the 1988 model year, International altogether retired the 6.9L IDI and in its place began producing the 7.3L IDI.
http://www.dieselhub.com/idi/7.3-idi.html

Sep 06, 2017 | Ford Cars & Trucks

1 Answer

My 93 ford f250, 7.3 IDI sounds like a rod is knocking when I first start it up but after it warms up it sounds very faint. What could be causing this noise?


The 7.3 idi engine is a compilation of ford and international engineering with a compression ratio of 21.5:1 ratio and produced 338 ft/lb of torque @ 1400rpm
It is an indirect injection engine (IDI) and the noise could come from a cracked pre-combustion insert that expands on compression heat and so reduces in sound. It may also be a faulty injector tip that is squirting rather than atomizing as it should
I would remove the injectors and have them tested at an accredited diesel repair specialist before going any further. Talk with a service centre for advice on the insert but as they are normally covered partially by the block there is a risk that they may come out or disintegration but it needs checking out.

Feb 05, 2015 | Ford Cars & Trucks

1 Answer

I have a 91 f350 7.3 liter idi. It will not start


cranks ok , and fast?
after checking all fuses. (the FSM shows correct fuse)

International Harvester IDI (from Indirect Injection) engine is a 4-stroke 8-cylinder Diesel engine used in International Harvester trucks,
like all diesels check fuel filters first. (service)
then make sure glow plugs work. (fsm covers this)
then scan it EFI for DTC errors. got errors?
direct injection uses EFI.

IF DIY, you need the book, I promise.....
its not simple like old diesels were.

May 03, 2014 | Cars & Trucks

3 Answers

My car will not run or starts and will not take the gas when it rains or damp outside. when it sets a day or two then runs great. What can it be. I was told it can be a module. Which one. yes 1996...


If your car is equipped with a 2.4L Quad 4 engine, you most likely need to replace your ignition coils. They are located inside what is called the "IDI Module" This is the large cover on the top of the engine that says "Quad 4". The ignition coil housing and spark plug boots should also be replaced. (See pictures below)

To replace the coils, disconnect the IDI electrical connector (Driver's side of the IDI Module) Remove the 4 bolts retaining the IDI Module to the cylinder head.

NOTE: be careful not to loose the washers under the bolts. Sometimes they will stick to the IDI Module and will fall off when you remove it. It is best to take a small screwdriver and get them loose before they have a chance of getting lost. Trust me...It happens all the time.

Remove the IDI Module from the cylinder head and flip it over. Remove the 4 screws holding the coil housing to the IDI module and remove the housing. Remove the screws holding the ignition coils and remove the coils. Reverse procedure to install.

IGNITION COIL

dttech_23.jpg

COIL HOUSING

dttech_24.jpg
SPARK PLUG BOOTS

dttech_25.jpg

May 22, 2011 | 1996 Chevrolet Cavalier

1 Answer

I have an Oldsmobile Alero GL 2003 & I'm not sure what size the engine is. I needed to know how many plugs are in it & the mechanic told me it takes boots not wires.


if the engine says its a 2.4. then it is a 4 cylinder ( 4 plugs ).on the 2.4 remove the four bolts on the ignition coil cover. pull the idi cover straight up until the boots are off the spark plugs, then set cover aside. if the boots stick to plugs, you can reatach them to coil cover on bottom of idi cover. thats it !! have a good day !!

Dec 07, 2010 | 2003 Oldsmobile Alero

1 Answer

1994 f350 7.3 idi turbo diesel location of oil pressure sending unit


on the 7.3 idi , the oil pressure sending unit is mounted on the oil tube on top of the turbo. that is if it is the original

Sep 26, 2010 | 1994 Ford F350 Crew Cab

1 Answer

Idie problems when starting, stops after a while


It sounds like the map sensore is loosing it's life. It's also quite possible that it just needs a tune up.

May 21, 2009 | 1994 Honda Civic

1 Answer

Firing Order for Spark Plug Wires for a cavalier v6 93


2.3 and 2.4 has idi ign.syst. mounted directly on top of plugs,2.2 coil pack cylinder numbers are marked on it,from left of elect. connector on coil pack is 2-3-1-4where spark plug wires go,on block, cyl. from drive belt side is 1-2-3-4,timing firing order is1-3-4-2

Mar 15, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1998 Jeep Wrangler Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...