Question about 1985 Nissan Stanza

1 Answer

Need info on replacing the front wheel bearings on my front wheel drive 1985 Nissan Stanza?

Posted by on

  • podfatherljv Jun 24, 2009

    The first guy gave me info on the wrong car and now this. By the way, I got the bearings, races, seals, and the Chiltons at the first local parts store before I got your reply.

    Thanks for trying.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 365 Answers

WOW...85? Go to AutoZone or Napa and order a Chiltons manual ($25)...
Good Luck getting parts

Posted on Jun 23, 2009

  • messstat
    messstat Jun 28, 2009

    Set up for a fall? You'd already arrived at a solution before you asked for help...and then had the brass to delve out a poor rating...I'm helping people for a reason...those unappreciative should not apply.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace cv joints on a 1985 nissan stanza


It's better to buy a manual. find them at you local auto part store. There isn't enough space in here to explain. I've replaced stanza cv before, just be careful, For your safety use jack stands.

Feb 12, 2016 | 1985 Nissan Stanza

1 Answer

Can anyone fill me in (in detail) on how to replace my front wheel bearings in my 2000 xterra? its 4 wheel drive and both fronts are bad.. also i cant figure the size of the caliper bolts out so that info...


Hit up www.nicoclub.com/FSM/xterra/2000/
That's the factory service manual which will provide detailed information.
There's an inner and outer bearing on each side

Sep 18, 2011 | 2000 Nissan Xterra

1 Answer

Cv shaft replace


This is usually the same on all front wheel drive cars..

Remove the wheel

Remove the brake caliper

Remove the brake rotor

Remove the spindle nut

Remove the wheel bearing assembly (usually 3 bolts)

-The next step may be optional, depends on the car-
Unbolt the lower ball joint (under the A-frame, some are riveted, if so, drill them out and chisel or just chisel them off with a metal chisel, sometimes you can cut the rivet heads off with a sawzall then pry it apart from the a-frame)

Pull the wheel bearing assembly from the spindle of the CV half shaft.
(Sometimes you need a wheel puller)

Once its loose, all you have to do it yank it out, and push the new one in. Make sure the new one pops in and is seated firmly.

Reverse steps for re-assembly. If you took the ball joint loose and it was riveted, use hardened steel bolts and nuts with lock washers to replace it, or buy a new ball joint, they aren't that expensive and it will come with bolts.

Good luck

May 09, 2010 | 1992 Nissan Stanza

1 Answer

Transmission started gushing fluid out.


THAT sounds like the foward pump housing cover and the only thing to do is to take it to the auto trans people as it has to be remover and replaced from inside
I could be wrong but i dont think so
LET ME KNOW HOW YOU GO Ron

Oct 03, 2009 | 1990 Nissan Stanza

1 Answer

Directions replace front wheel bearings on a 1985 nissan stanza?


996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Jun 23, 2009 | 1985 Nissan Stanza

1 Answer

Nissan Stanza 1986 car bucks and cuts out when accelerating


I would check the vacuum advance. or maybe an O2 sensor

Feb 19, 2009 | 1985 Nissan Stanza

2 Answers

How to replace front wheel bearings and CV joints on a 1991 Nissan stanza


I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Jul 24, 2008 | Nissan Stanza Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...