Question about 2006 Ford Five Hundred

1 Answer

Removed battrey cable now car want run

Car not getting fuel after it cranks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 51 Answers

This is confusing so by removing battery cable I assume you mean to the coil or ignition module, as the car is cranking over.
Go to here http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/06500og1e.pdf turn to page 192. Locate and check fuse F14 and F18. see page 193. Also on pg 196 I would check fuse 27.
If it is none of these and you definitely have fuel in the car, then it is most likely a blocked fuel filter or dead fuel pump.

Posted on May 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford explorer xlt 4.0 cranks will not start took to garage changed battery cables and cleaned charging system 2 days later cranks will not start but can hear fuel pump running when I turn key the...


You should hear the fuel pump run momentarily when the key is in the Run position. Ensure the engine has a good spark by removing one of spark plug boots. Stick a phillips screwdriver in the boot, and hold the handle of the screwdriver, and allow the shaft near ground. (motor works best) Have someone crank the engine and look for a good blue spark arch from the screwdriver and engine. If your getting good spark, then check the fuel pressure on the fuel injection rail.

Nov 17, 2014 | 2000 Ford Explorer

1 Answer

Where is the fuel filter located


FUEL FILTER LOCATED UNDERNEATH THE CAR NEAR THE FUEL TANK.YOU NEED TO RELIEF FUEL PRESSURE BY REMOVING REAR SEAT CUSHION,REMOVE ACCESS PANEL,REMOVE FUEL PUMP MODULE CONNECTOR ,START THE ENGINE AND ALLOW IT TO RUN UNTIL IT STALLS, THEN TURN OFF VECHICLE.PLACE A REMINDER OR WARNING NOTE ON STEERING WHEEL NOT TO CRANK CAR YOU ARE REPLACING FUEL FILTER.THIS KEEP SOME ONE FROM ACCIDENTALLY CRANK CAR WHILE YOU WORKING ON IT.YOU CAN DISCONNECT NEGATIVE BATTERY CABLE BUT YOU WILL LOSE RADIO CODE AND PCM MEMORY.

Sep 28, 2010 | 2002 Hyundai Accent

2 Answers

Wont crank changed crank senser


check starter check for low battrey volltage

Jul 25, 2010 | 2004 Dodge Ram 1500

1 Answer

How do I change the front fuel sensor on a 51 plate freelander


get a new fuel pump and screen then drop the gass tank get hi pressuer clamp releasher dis conect the battrey releave the gas pressure on the fuel rail befor you themp to remove the clamps on the gas tanks the replace the whole fuel pump and screen note replace the fuel filter allso

Feb 18, 2010 | 2002 Land Rover Freelander

1 Answer

RX6 2005 won't crank after a short start up to move car out of way and parked.


I removed the fuel pump fuse to stop fuel from getting to the rotary chamber which was flooded to begin with. After "MUCH" cranking [using a jumper cable from a second battery/car] and keeping the accelerator fully depressed we purged the chamber and the engine fired. When the engine started we replaced the fuel pump fuse to keep it running. Total process was longer than 60 minutes with time out(s) to rest the starter so we did not burn it out while letting the battery regain 'full' charge as this rotary engine requires a fast cranking rpm to start.

Jan 29, 2010 | 2004 Mazda 6

1 Answer

I'm not getting fuel or spark and the inertia switch is not tripped


you can check for your fuel system, put the key in mar position and feel some noise from fuel tank, if noise is there then fuel system is workin, and after taht remove one high tensin cable from spark plug and crank the eng before cranking put one screw driver inthat open cable while cranking you will find somr rays coming out from screw driver to body of the engine hold it 5 cm away from engine body,(DONT KEEP ANY PART OF YOUR BODY TOUCHED TO THE SCREW DRIVER OR CAR WITHOUT INSULATOR).thanks.

Jan 16, 2010 | 1992 Ford Explorer

2 Answers

I'm working on this problem for our church's car care ministry. 2002 saturn, has had battery, alternator, and fuel pump replaced. had a check engine light. car will not start. what would be some areas to...


Check is current is flowing in the cables to each plug(4)! Remove any of these cables and hold it near any metal(engine block) and have someone crank it. If sparks are not coming out of the cable, then the induction coil needs to be replaced, Follow it up by checking the distributor, if present(doubt), and check the contact points for deposition of carbon...........sodeep

Nov 10, 2009 | 2002 Saturn Sl

2 Answers

Wont start, cranks strong.


fuel pump, computer, anti theft system,crank sensor

Oct 14, 2009 | 1998 Ford Mustang

1 Answer

1992 Ford Taurus wagon not starting, but turns over


You might have a problem with your crank sensor or ignition. Remove spark plug wire and check for spark while turning engine over. When this happens unplug crank sensor near crank pulley then plug back in to see if it starts if so replace crank sensor.

Jul 29, 2009 | 1992 Ford Taurus

1 Answer

Help!


key off and out,diconnect negitive side of battrey then postive.clean terimals,charge battrey,connect postive cable (with key off)connect negitive.and start.
your dead battrey is taking up a big load on system,so when you boost it the dead battrey is taking it all the starter is geeting vey little.thats the clicking.
if you dont have a charger dicconect both terminals the same way again,put the jumper cables on the dead battrey.let it charge battrey for 10 15 mins .the longer the better.remover jumpers.
with key off and out conected battrey terminals.connect jumper cables and start.
let me know if it start or not hopefully the key hasnt lost its coding.

Dec 04, 2008 | 2003 Volkswagen Golf

Not finding what you are looking for?
2006 Ford Five Hundred Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...