Question about Jeep Grand Cherokee

1 Answer

I need 02 jeep 4.0 wiring harness diagram

Putting a motor in jeep and i have one plug on harness that i cant find termination point approx top of trans close to bell housing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Alldata.com
login and read, its all there all the time.

02 cherokee is here
tripler posted too, (backup and read them?)
why not post the full car spec, as it was built.
we dont know that, nor did you post a photo of conn.
no the wire colors, nor country.
In the USA,the colors of the wires are USA colors. (they have export models too. and wired diffr.)
so no photos, no colors , and no drive line options, stated
mine was a 5sped, with 4wd.
see? i bet mine was different from yours, no?
the FSM covers all this,

free is here.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

get a subs.
and login here. for $15 lousy bucks. why beg for facts and worse get bad advice, nobody knows what in your jeep. nobody.

http://www.scantool.net/software/alldata-diy-1-month-subscription.html

facts.
many connectors on a car, are NOT USED,
that is because they dont make a harness for every permutation of DAY 1 (as built) OPTIONS.

Does something not work, if yes, say what it is.?
my FSM shows the shematics in 3 ways,
simple schem.
actual schem.
and the harness physical routings. and the connectors and pins and names of each one. so I you had the FSM in hand.
all that would be easter egg easy.

(like cruise control conn. 1, missing, because, its not opted)

Posted on Jun 03, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrSocket
  • 117 Answers

SOURCE: Need diagrams for 88 Jeep Wrangler Auto Trans

Your public library will have a manual covering your mechanical repair. Moreover, they have the automotive shops online software called AllData. It is the best auto technician database available today. You can print out specific troubleshooting procedures, diagrams, step-by-step istructions, and soforth. The typical person cannot afford to pay for this service, just automotive dealerships, etc... that is why the public library made it available to everyone and for free to view and print out material. This should Fixya! Good Luck!

Posted on Aug 28, 2009

  • 181 Answers

SOURCE: Installing 2008 F-350 Engine into 2002 F-350 Need wiring diagrams

I find what I need @ powerstroke.org. Great website with lots of Information and its free.

Posted on Aug 29, 2009

  • 8 Answers

SOURCE: Need advice on 1994 Jeep Wrangler Engine Swap

is this jeep a daily driver email me your number and ill help you decide chevy726992@yahoo.com

Posted on Oct 05, 2009

BCAS1298
  • 3092 Answers

SOURCE: I have a 1996 jeep cherokee 2wd 4.0L and it is

Yes, in back of your engine block, there two freeze plugs, these plugs hold water or coolant in the block, to replace these freeze plugs, transmission will have to be remove, if your going to get this done, I would also have the rear main seal replace at the same time, should not cost you much labor to do this, due to if it starts to leak oil from there in the future, transmission will have to come out again, this will save you money and time down the road, hope this was very helpful.

Posted on Aug 19, 2010

e-Guru
  • 3917 Answers

SOURCE: someone cut the wiring harness

Hi

1998 GMC Sierra 1500 Remote Starter Wiring Diagram
Vehicle Battery Positive Wire (+): Red
Vehicle Battery Positive Wire Location: Ignition Switch Harness
Vehicle Ignition Wire (+): Pink
Vehicle Ignition Wire Location: Ignition Switch Harness
Vehicle Second Ignition Wire (+): White
Vehicle Second Ignition Wire Location: Ignition Switch Harness
Vehicle Accessory Wire (+): Orange
Vehicle Accessory Wire Location: Ignition Switch Harness
Vehicle Second Accessory Wire (+): N/A
Vehicle Second Accessory Wire Location: N/A
Automobile Engine Starter Wire (+): Brown
Automobile Engine Starter Wire Location: Ignition Switch Harness
Automobile Second Engine Starter Wire (-): N/A
Automobile Second Engine Starter Wire Location: N/A
Factory Anti-Theft System: Passlock II Vehicle Immobilizer
Factory Anti-Theft System Type: Key Sends a RF Signal to the BCM Module
Crankshaft Sensor Wire: N/A
Crankshaft Sensor Wire Location: N/A
Camshaft Sensor Wire: N/A
Camshaft Sensor Wire Location: N/A
Car Key Sense Wire (-): Light Green
Car Key Sense Wire Location: At Steering Column Harness
Car Neutral Safety Wire (-): N/A
Car Neutral Safety Wire Location: N/A
Car Tachometer Wire (-): White
Car Tachometer Wire Location: At Ignition Coil
Car Speed Sense Wire: Green/White
Car Speed Sense Wire Location: In Harness on Driver Side of the Engine Compartment
Car Parking Lights Wire (+): Gray/Black
Car Parking Lights Wire Location: At Vehicle Light Switch
Car Brake Lights Wire (+): White
Car Brake Lights Wire Location: At Switch Above the Brake Pedal
Car Reverse Lights Wire (+): Light Green
Car Reverse Lights Wire Location: Pin F in Black Plug at BCM Module
Car Horn Wire (-): Black
Car Horn Wire Location: In Harness at Steering Column
Car Rear Defrost Wire: N/A
Car Rear Defrost Wire Location: N/A
Also check the bellow links for the wiring diagrams, hope they help:-
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp;jsessionid=074138E4E86673F4D85504D965DB7685.diyprod2-b2c12?chapterTitle=Wiring+Diagrams&partName=Chassis+Electrical&pageId=0900c1528008f3ce&partId=0900c1528008f2c2
http://www.2carpros.com/questions/gmc-sierra-1998-gmc-sierra-wiring-diagram-for-firing-orde
http://www.the12volt.com/installbay/alarmdetail/1000.html
http://www.the12volt.com/installbay/forum_posts.asp~TID~7482

Please get back to us if you have further query else please accept the suggestion.
Thank you for contacting fixya.com

Posted on Apr 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find a wireing harness for a 1996 Dodge ram 2500 Diesel ? I need the headlight harness


You have to pull it any way. Fix the one you have. It is way easier to find new plugs for them, than the entire harness. I just did an 02 jeep. Found a couple jeeps at the junk yard. (dealer obsolete) The harnesses were cut to pieces. The plugs I needed, I found at the parts store. Had to repair wires also.

Aug 23, 2016 | 1996 Dodge Ram

1 Answer

I need a diagram to put a wiring harness from a 1994 4.0 jeep wrangler in a 1993 4.0 jeep wrangler


check chiltons manuals, they usually have wiring diagrams in the back of them to show you all you need. its hard to find online ones. you always have to pay for those ones

Mar 21, 2012 | 1994 Jeep Wrangler

1 Answer

I have got the starter diconnected from my 2005 5.7 jeep gc but I cant get it out to replace it


1. Disconnect and isolate negative battery cable.
2. Raise and support vehicle.
3. Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt.
4. Remove two mounting bolts (2).
5. Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor (1) during this process, do not let starter motor hang from wire harness.
6. Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness.
7. Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud.
8. Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle.
9. Remove starter motor.

May 14, 2011 | 2005 Jeep Grand Cherokee

2 Answers

2001 jeep wrangler 2.4l spark plug wires were disconnected I need the wiring diagram to reconnect


2.5L engine. 1 3 4 2 Number 1 should be approx 5 o'clock position, the order goes clockwise.

Mar 11, 2010 | 2001 Jeep Wrangler

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

2 Answers

2002 jetta tdi died while shifting into 4th gear


Sorry, not a solution to this car but your other vw 1989 jetta...only way I could get hold of you.

here is your diagram

The following information covers electrical connections and plugs to the rear of the fuse/relay panel. It completes and supplements the information in the appropriate Service or Repair Manual for the fuse/relay panel section and should be used in conjunction with the wiring diagram for the vehicle or system in question. Volkswagen part numbers shown here may or may not match those on your panel, however, if you panel visually matches the diagram, it is correct for your application.
Fuse/Relay Panel - Rear Connections (Volkswagen Part Number 171 941 821 D) clear.gif
97-3228.gif
Connections and plugs on rear of fuse/relay panel:
A Blue 28 pin Instrument cluster wiring harness B Red 28 pin Instrument cluster wiring harness (position 5 open) C Yellow 22 pin Engine compartment/engine management, left side (position 10 open) D White 29 pin Engine compartment/wiper motor wiring harness, right side (position 6. 10, 14, 18, 27, 28 open) E Black 18 pin Rear wiring harness (position 17 open) G n/a 1 pin 10 individual circuits H Brown 6 pin Air conditioning/coolant fan relay wiring harness K Neutral 5 pin Seat belt warning system/coolant level wiring harness L Grey 4 pin Horn wiring harness L Black 4 pin Headlight/dimmer switch wiring harness M Black 2 pin Steering column switch wiring harness M Black 2 pin Headlight/dimmer switch wiring harness N Red 1 pin Separately fused circuits (glow plug wiring harness) P Red 7 pin 7 single point connectors for terminal 30 circuit R Green 2 pin Open/ECM power supply relay
Note: Terminal and harness assignments for individual connectors will vary depending on vehicle equipment level, model, and market. Always consult appropriate wiring diagram for specific terminal assignments.

hope this has resolved your problem

Thankyou

Aug 15, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

I am installing a wiring harness for my 2005 jeep liberty but i am not sure what each color stands for


harness plugs are all different and really cant be plugged in wrong. When removing old harness make note of what connectors are used and find them on the new harness before installing it. wires inside the harness are tied together in different places and if you are using a harness from a different year vehicle, you need to trace out each wire and it's destination points and match pin positions before using. You can use an ohmeter with an audio "ringer" on it to do this.

Jun 15, 2009 | 2005 Jeep Liberty

2 Answers

Motor and trans exchange


Both engines were available in that jeep, but computer and harnesses need to be swapped as well. You may want to get a really good wiring diagram (not haynes) to check your attachment points and harness variations. Make sure you take everything you could possibly need from donor vehicle. (take more and throw away excess...easier than forgetting something.)
Good luck!!

Apr 10, 2009 | 1986 Jeep Cherokee

2 Answers

Diagram for 91 jeep cherokee plug wires


For a 4 the firing order is 1234 front to back and the distributor fires clockwise. Find one and run wires from there.

For a 6 its 123456 front to back and is also clockwise.

Joel

Dec 27, 2008 | 1991 Jeep Cherokee Briarwood

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...