Question about 2004 Suzuki Verona

1 Answer

How do I replace O2 sensor, bank one sensor one

Need to figure out location, Ive been told drivers side is bank ine, sensor one is the upper one . . .

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 15,557 Answers

Bank 1 sensor 1 is the location on the exhaust manifold. Look for all the metal pipes coming off the engine in a tree like configuration. The sensor is mounted there. You need to have a socket that allows for the wire. The socket looks like it has a split up the side.Also you need to see about using high temp anti seize compound on the new one.

Posted on May 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: po153 eobd code

Bank one Cat is always on the side where # 1 cylinder is located. this is called bank one by Federal standardization rules, on OBD 2 Terminology and code definitions.

Posted on Oct 22, 2008

DAD5bbbbg
  • 111 Answers

SOURCE: directions on replacing the oxygen sensor

Start at the exsoust manifolds.follow it back and you will find the o/2 sensors. I would spray them with WD 40 before you try to take them out. most of them can be very tight and hard to get to. make sure that you unpulg them and check the wires to make sure they are on.

Posted on Mar 03, 2009

daves944
  • 1050 Answers

SOURCE: 2004 suzuki verona..where is bank 1 senor 1 located on the engine

This car has a transversely mounted straight six I believe, which is really unusual, but that means it only has one bank, so "bank 1, sensor 1" will be the upstream O2 sensor (between the engine and the cat) and "bank1, sensor 2" will be the downstream sensor (behind the cat).

Posted on May 10, 2009

daves944
  • 1050 Answers

SOURCE: 2004 suzuki verona 6 cylinder

It should be in the exhaust downpipe, between the engine and the catalytic converter.

Posted on May 10, 2009

Lloyd Six
  • 560 Answers

SOURCE: OBD II code P0133 (O2 bank 1 sensor 1) which

It is the front sensor, if your car is the type that has 2 front sensors it will be the one closest to the timing chain / belt (left hand side of engine)

Posted on Nov 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Nissan Frontier 3.3l v6 I'm about to change my knock sensor but I also need to change the camshaft position sensor but I'm not positive of where it is located it say bank 1??????


I'm willing to bet you have weak upper O2 sensors & there's nothing wrong with your knock sensor. But if you want, the knock sensor is under the lower intake manifold in the back that is located under the upper intake manifold also called the upper plenum. The lower intake manifold is wedged between the 2 heads and is an enormous pain in the azz to get to. You can check the O2 sensors with a scanning tool that will show you the upper sensors in bank 1 & 2 bouncing electrical current from about .5v to 5v several times per second. Anything less show weak sluggish sensors. The resulting lean mixture causes a knock. Change the sensors and the knock goes away and so does the engine light after you reset it. It took me 6 months to find this problem after replacing everything else including the 6mth old O2 sensors fresh from China. Now I have Bosch. PS The lower sensors went 2 weeks later & I was told any more problems it's the fuel regulator. 2001 Frontier 3.3l v6. No problems since, it purrs like a kitten. I'd suggest the Bosch, it's a special design for that 3.3l engine.

Sep 14, 2015 | Nissan Cars & Trucks

1 Answer

How many o2 sensor are on a 2004 gmc yukon


Hi Charles,

GM products have 4 O2 sensors attached along the exhaust pipes coming off the manifold. Bank 1 is aligned to cylinder 1 on the engine which is the driver's side. Sensor 2 is the one after the convertor (Sensor 1 being the one before the convertor). Link attached for more information.

Oxygen Sensor Locations

I have changed out one of mine; quite easy, but you need a sensor wrench which you can find an any automotive store for around $15.

The part is available readily enough - link attached.

Good luck

Feb 07, 2015 | 2004 GMC Yukon

1 Answer

Location bank 1 o2 sensor


It's screw into your exhaust manifold.

Sep 28, 2013 | 2000 Nissan Altima

1 Answer

After fill ups, engine light indicates deffective 02 sensor bank1. On a '04, Dodge Grand Caravan, 3.8.


You must have duel exhast then. Bank 1 is the drivers side and you have a upper and lower o2 sensor. More than likely it is the upper o2 sensor that is the problem.

Aug 12, 2012 | 2004 Dodge Caravan

2 Answers

97 Blazer.. o2 sensors


Hi, dont worry. bank one is the drivers side and the sensor 1 is the upper sensor above the catalytic converter. and the bank 2 is the passenger side. good luck

May 22, 2010 | 1997 Chevrolet Blazer

1 Answer

Where is bank one oxygen sensor located at on a 2003 yukon


Need more information but here is where all your O2 sensors are located
Bank 1 Sensor 1 - Driver's side, before catalytic converter Bank 1 Sensor 2 - Driver's side, after catalytic converter
Bank 2 Sensor 1 - Passenger side, before catalytic converter
Bank 2 Sensor 2 - Passenger side, after catalytic converter

Thank you for using fixya and good luck

May 13, 2010 | 2003 GMC Yukon XL

1 Answer

Where is the location of the bank one sensor one o2 sensor on my 2003 chevy suburban


bank 1 on a chevy is on the drivers side youll have 4 O2 sensors sensor 1 bank 1 is on the engine side of the cat converter sensor 2 bank 1 is after the cat converter (drivers side )
bank 2 is on the passenger side sensor 1 is pre cat sensor 2 is post cat converter

Mar 18, 2010 | 2003 Chevrolet Suburban 1500

2 Answers

Need to know location of Bank 1 Sensor 1 on engine


If I am not mistaken bank one should be your driver side. However your sensor one will be before the cat converter. So you just have to find the o2 sensor before the cat converter on the driver side. Good Luck.

Oct 12, 2009 | 2003 Acura 3.2TL

1 Answer

CATALYTIC CONVERTOR - BANK 2


You have a V6 engine, bank one is the row of cylinders on the passenger (right) side, bank two is the row of cylinders on the drivers side (left). Your codes indicate an inefficiency in the cat on the left side but this could be due to a bad O2 sensor or an engine that is out of tune and overloading the cat. This car seems too new to have a bad cat. I would change the plugs and the O2 sensor after the cat before going any further. The reason I say the O2 after the cat, it's the one that is critical in sensing cat efficiency. What is the mileage?

Mar 26, 2009 | 2005 Mitsubishi Galant

Not finding what you are looking for?
2004 Suzuki Verona Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...