Question about 2010 Hyundai H-1 Travel

1 Answer

Now what the next step

Hi i have clear the codes we rebuilt fuelpump and injectors now i scan agian no codes but the engine malfunction still

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 70 Answers

I do not Know what kind of Diagnostic equipment You have ?? but
if you can monitor 02 Sensors and Mass Air Flow sensor see if anything looks erratic I usually run RPM at around 1000RPM and Run up to 2000RPM adjustments should be smooth and consistent with your Throttle position sensor held steady at 10 percent or so are Your sensors readings staying steady or jumping around if erratic need further diagnosis of sensor or replacement
also check crank sensor to timing see if they are in sync
next does it change any from Park /Neutral to when you put it in gear modern vehicle's rely a lot on signals from transmissions to control ignition

Good Luck Rickie

Posted on May 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 grand caravan 3.3L starts up and stalls possible causes would be?


code 27...injector control circuit malfunction ! The wiring is open or the computer is bad . There are videos on youtube checking injector control circuits and the driver inside the PCM/ECM -engine computer . How to test fuel injector circuit with basic tools open control wire

Jan 27, 2017 | Cars & Trucks

1 Answer

Misfiring


remove the spark plugs on the front and inspect. if the first one is wet and dark you need ignition coil.swap the coil with next cylinder clear code and run for a minute or till the check engine light come on.scan for code.if the code move with the coil you need coils.
if the code is the same run the engine and listen the injectors for ticking noise .crisp and clear noise is good.low tone or no click injector is bad.some times the wire going to the back is broken and will short two cylinder at the time

Mar 31, 2014 | 1998 Toyota Avalon

1 Answer

Engine misfire and flashing check engine light


P0205 Chevrolet Injector 5 Control Circuit You have a bad injector , burnt PCM driver or a wiring problem . Videos on youtube. How to test fuel injector circuit with basic tools open control wire

It's not an ignition system problem !

Mar 12, 2017 | 2003 Chevrolet Impala

1 Answer

Not recieving fuel to the injectors,fuel pump new and fuel filter new. the engine was just rebuilt


PROBLEM IN ECM IT FIRES FUEL INJECTORS, BEST TO HAVE VECHICLE CODE SCAN BEFORE SPENDING WHOLE LOT OF MONEY ON NEW ECM.

Aug 08, 2011 | 1997 Mitsubishi Eclipse

1 Answer

My 2000 toyota celica gts has no fuel pressure to the fuel rail


this may be a few things that would cause this problem, first is the anti theft system, try another key first and see if it starts, if so then key is bad. the next step would be to scan the computer for any stored codes as these codes will help alot in find the problem, but if thats no a way due to the car not running then the next step would be to check for power at the fuelpump. if theres power at the pump then the pump is bad. you can try having someone beat on the bottom of the fuel tank with a rubber hammer and at the same time try starting it and if it runs then replace the pump, if theres no power at the fuel pump then check all fuses first and then try swapping the fuelpump relay with another relay with the same numbers to make sure the relays are the same. start with these things first. good day.

May 15, 2011 | 2000 Toyota Celica

2 Answers

Why has my malfunction indicator light come on my Suzuki Liana and how do I solve it?


The check engine light comes on when the vehicles computer detects a problem with one of many operating systems it monitors and controls. You will have to have a diagnostic code scan performed to determine which system the computer has found a malfunction with and repair as necessary.

Feb 21, 2011 | 2006 Suzuki Verona

3 Answers

98 jeep wrangler 4.0 6 cyl auto spits and sputters under load


Hi JHWalker
I would try doing the fuel pump filter or fuel pump itself if they are one unit.

Hope this help you.

Matt

Sep 18, 2009 | 1992 Jeep Wrangler

Not finding what you are looking for?
2010 Hyundai H-1 Travel Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...