Question about 2002 Infiniti G20

2 Answers

Getting fuel to the rail but will not start what is the problem

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Infiniti Master
  • 3,679 Answers

Have the OBD codes read as this will pinpoint the sensor/switch that is faulty etc , i'd guess at ignition problem but there are a few causes so get the OBD done

Posted on May 14, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Infiniti Master
  • 40,764 Answers

Check why the injectors are not getting a pulse .Check cam/crank position sensors. Check that the cam shaft is turning ( broken belt/chain)

Posted on May 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1996 Silverado 5.7 Won't start . I replaced the fuel pump and it is getting fuelto the rail but won't inject. If I prime it at the throttlebody it will start.What could be the proble?


Verify the fuel pressure is 60-66 psi at the fuel rail. Fuel pressure regulator could be the problem.
Next, Photo shows a common problem. 25281328-eiq04jcqehklpmop1towry5q-1-0.jpg

Nov 13, 2014 | Cars & Trucks

1 Answer

1999 Olds Alero will not start until press is released in fuel injector rail


It could be that the fuel pressure is too high. This COULD cause the injectors to not fire when they are triggered. Once you bleed the pressure and the car is running, there is enough flow to keep the pressure at a manageable level. I would get a fuel pressure gauge and check the pressure at the rail. You may find a new fuel pressure regulator will fix your issue.

Dec 18, 2013 | 1999 Oldsmobile Alero

1 Answer

My 1994 ford crown victoria will not start no gas is going from the fuel regular to the fuel rail to the injector


how much pressure are you getting at the fuel rail? you also need to check the impact shutoff switch to make sure it is not tripped, it will be a black box usually behind one of the kick panels, with a button on it press the button down to reset then try stating the car

Jul 23, 2012 | 1994 Ford Crown Victoria

2 Answers

I need to access the fuel injectors in my 98 wrangler, but i dont know how to get to them


FIRST NEED TO RELIEF FUEL PRESSURE REMOVE GAS CAP RELIEF GAS PRESSURE IN FUEL TANK.THEN REMOVE FUEL PUMP RELAY THEN START ENGINE UNTIL IT DIES LACK OF FUEL,CRANK ENGINE OVER FEW MORE TIMES MAKE SURE FUEL OUT OF FUEL LINES. THEN YOU NEED TO REMOVE AIR CLEANER CROSS OVER TUBE ABOVE FUEL RAILS. DISCONNECT LINES AT THE ENDS OF THE FUELS RAILS ASSEMBLY. MARK AND DISCONNECT THE FUEL INJECTOR WIRE HARNESS CONNECTORS. REMOVE THE FUEL RAIL RETAINING BOLTS, DISCONNECT THE VACUUM LINE FROM THE FUEL PRESSURE REGULATOR. REMOVE THE FUEL RAIL ASSEMBLY FROM THE ENGINE. IF YOU HAVE AUTOMATIC TRANSMISSION REMOVE THE THROTTLE PRESSURE CABLE AND BRACKET TO REMOVE THE FUEL RAIL ASSEMBLY.TO REMOVE FUEL INJECTORS JUST REMOVE CLIPS THAT RETAIN FUEL INJECTORS IN FUEL RAIL. BESURE GO TO DEALERSHIP BUY NEW FUEL INJECTORS O - RINGS.APPLY A SMALL AMOUNT OF ENGINE OIL TO THE O - RINGS TO AID IN INSTALLATION. TORQUE FUEL RAIL BOLTS TO 100 INCH LBS.

Jun 19, 2011 | 1998 Jeep Wrangler

1 Answer

Fuel injector reeplacement


you don`t say what motor is in this so here is a basic procedure, find the fuel rail where the fuel lines connect to at the intake manifold.disconnect the fuel lines(be carefull you could get gas in your eyes from fuel spray or start a fire due to hot engine)these lines have high pressure fuel in them.look at the fuel rails to see what all is in the way to remove them and remove interferance items.remove the bolts that hold the rails to the intake manifold,gently lift wiggle the fuel rails and you may have to pry up on the rails in places to get them to come out with the injectors attached the rails.you should make sure any debris is removed from around the injectors so no dirt falls into the injector holes before you remove.then you can remove the injector to rail lock clips and remove the injectors from the rails.clean areas were the injectors will be going apply either gas or silicone on the injector O rings then install injectors to rail install lock clips and reassemble.replace all the O rings as they get dried out brittle and crack or split.re-install removed components start car and check for fuel leaks.

Mar 02, 2011 | 1998 Oldsmobile Silhouette

2 Answers

After removing the fuel injectors and rail to remove the manifold, how do you reinstall the fuel injectors?


the same way you took it apart. put a little grease around the rubber seals so they will slide in easier. just tap on the fuel rail while lightly tapping it into place.

Mar 28, 2010 | 2002 Honda Passport

1 Answer

96 buick road master fuel problem


sounds like a fuel pressure regulator issue or even the sending unit is going bad one of the two what is the pressure at the rail ? you can often get one from a parts store

Sep 07, 2009 | 1993 Buick Roadmaster

2 Answers

Car will not start Have fuel to rail


It may not be a fuel problem Try a small shot of starting ether in the air intake. If it starts quick and shuts off it's a fuel problem but if it doesn't start start it's electrical.
Jack

Jan 31, 2009 | 1997 BMW 318

Not finding what you are looking for?
2002 Infiniti G20 Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14204 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...