Question about 1991 GMC S-15 Jimmy

Open Question

How do you have to remove the ecm from behind glove box ?

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 4669 Answers


Remove the glove box, you will see the relays, sounds like a bad ground.

Posted on Feb 27, 2009

  • 14411 Answers

SOURCE: how to remove cabin filter in the plenum behind the glove box

Our research indicates that your vehicle does not have a cabin air filter (also known as a pollen or AC filter). Vehicles without cabin air filters typically have a plastic mesh that prevents leaves and other foreign objects from entering the HVAC system. This mesh is part of the vehicle and does not need to be changed.

Posted on Sep 19, 2016

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to replace ecm on 1993 buick century?

remove knee bolster on the passenger side and find the ecm under the dash behind the glove box. some of these you can remove the inner glove box to give you more room. it is held in a bracket that you will have drop down and unbolt the holding fasteners that hold the ecm in the bracket then disconnect the plug connectors to the ecm.

Aug 05, 2014 | 1993 Buick Century

1 Answer

Ecu removal instructions

That begs the question of WHY are you wanting to remove it?

Anyway, the ECM is located behind the glove box. Remove the glove box to get to the ECM to remove it.

Also please note that if the ECU is replaced, it must be programmed to work with the onboard secuity system - or the engine will not start and run.

Mar 05, 2012 | 2003 Toyota Camry

1 Answer

Where is the transmission control module located?

The TCM is part of the ECM (electronic control module) and is not a separate module. The ECM is located behind and to the right of the glove box, you will need to remove the glove box liner to gain access to it. It has a large 60 wire connector going to it.

Aug 03, 2011 | 1994 Chevrolet C1500

1 Answer

Need pic of 1990 ford thunderbird ECM location and removal. ASAP please

I don't have a pix. but, check behind the glove box or under the right side if the dash.

becareful not to break the plastice clips on the glove box.

Dec 26, 2010 | 1990 Ford Thunderbird

1 Answer

I am trying to locate the ECM in my 1997 Toyota 4runner.

Hello ironshepherd
The ECM is located behind the right side of the dash just above the glove box. If you remove the
glove box, it should be fairly easy to access. Hope this helps.

Dec 08, 2010 | Toyota 4Runner Cars & Trucks

1 Answer

Trying to find the engine control module for 1991 olds cutlass siera sl

The ECM is located right behind the glove box. First remove the negative (-) battery cable. Then remove the front of your glove box, just a few small screws. The interior of the glove box is cardboard and will pull out after removal of screws. Then unplug the 3 electrical plugs and let them hang out of the way. Now, remove the bolts on the side of the bracket holding the ECM IN.

Nov 17, 2010 | 1991 Oldsmobile Cutlass Ciera

1 Answer

How do you fix a fan sensor in a 2000 malibu

are you talking about heating fan resistor! if so, this is where and how its replaced. it is behind glove box. remove glove box so you do not have to stand on your head, only about 7 or 8 screws. then loosen and slide ecm to one side. ( but when removing glove box, remove insulator panel under glove box first ) now you can see heater blower and resistor. it is beside the fan, remove the wires from it. take out holddown screws, then pull it out. have a good holiday!!

Oct 08, 2010 | 2000 Chevrolet Malibu

1 Answer

Check engine light comes on intermittently

Not, the check engine light show one advise of malfunction from someone of your components. If you can snaning you system, can knowed what code is showing. So, after you can make an action.

ECM location: behind the glove box, remove the screw a the right of the glove box and pull gently.

Hope helped (remember rated this help) Good luck.

Nov 20, 2009 | 2005 Toyota Corolla

1 Answer

Module missing behind glove box

Probably the ECM, the main computer

Jan 11, 2009 | 1997 Chevrolet Camaro

Not finding what you are looking for?
1991 GMC S-15 Jimmy Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides