Question about GMC Sierra

1 Answer

How do I take a cam shaft sensor inside a GMC sierra distrubuter?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • GMC Master
  • 808 Answers

Place engine on TDC by putting crankshaft balancer groove in line with timing cover pointer slot this is located between water pump and power steering pump then remove cap mark rotor pointer location for install indexing then remove drive pin onshaft that hold drive gear on mark gear to put on the same way remove shaft replace sensor reassemble

Posted on May 16, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

When i disconnect the tan/black wire to set timing engine will not hold steady idle. is this normal?

NO it should just stop the spark advance .Look at the cam and crank pisition sensors
More then likely the crank pisition sensor

Apr 19, 2015 | 1994 GMC Sierra

2 Answers

Do we set the timing after changing the cam shaft sensor on a 2002 GMC sierra 1500?

It would probably be a good idea but if that doesnt work try plugging in an error decoded and see if it comes up with anything

Aug 15, 2014 | 2002 GMC Sierra 1500

1 Answer

How do i time the cam sencer witrh the crank sencer ?

your question is realy garbled but I think you are asking about the timing of the cam and the crank sensors usually you have to have them both replaced at same time which means you can see the NO1 position on the cam and the position of the crank and thats with the cover off but I found out from another friend that if you go onto YouTube and request How To set timing on the Cam shaft and Crank shaft sensors you will get a video. MAKE SURE YOU SPELL IT ALL RIGHT OTHERWISE YOU WILL NOT FIND IT. Sorry about the Caps but wanted your attention use my spelling. Good Luck

Jul 22, 2014 | 1997 GMC Sierra

1 Answer

Where is the cam shaft sensor located in a 1996 jimmy 4.3litre engine

On V6 engines with a distributor, the sensor is inside the distributor.

Jun 10, 2013 | GMC Cars & Trucks

1 Answer

I have a 01 gmc jimmy that runs at idle, but stalls when i try to give it gas,and it give off fumes that burn your eyes.I already replaced the spider injectors ,cam,and crank shaft sensor

Check the rockers and if they are tight if not tighten them just enough to where you can twist the push rod with you fingers.Let me know if that works.

Oct 10, 2012 | 2000 GMC Sierra

1 Answer

2006 GMC Sierra with 5.3lt 8 cyl engine 4x4. Key on, all lights warning lamps light up.Turn key to start and all warning lamps turn off.Engine not starting,Checked battery,ok.Starter was replaced two...

code p 0654 refers to engine rpm output--circuit malfunction ===causes wiring ---ECM
code p 0650 refers to malfunction indicator lamp(MIL)--circuit malfunction====causes wiring --MIL---ECm
also refers to crankshaft position/cam shaft position sensor bank 1 sensor A --correlation===causes wiring---CKP sensor ---CMP sensor--mechanical fault

Jan 27, 2018 | 2003 GMC Sierra 1500

1 Answer

Where is the cam sensor on a 2004 gmc sierra with a 5.3

lcorgiat_30.jpgThis sensor is at the center rear of block

Feb 07, 2011 | 2004 GMC Sierra

2 Answers

1998 GMC Sierra 2500 5.7L hard cold starts last month, now won't start cold w/o a little carb cleaner in intake. Codes for oxy sensors, mass air sensor and crank/cam position. Drove today, no power just...

starting definately has a lot to do with the crank/cam position sensors, but it wouldnt have nothing to do with hot or cold weather, oxygen sensor will make the vehicle run too rich if its out, you will smell fuel very strong out the exhaust, that could make it run sluggish also, and usually if the mass air flow sensor goes out the vehicle wont start at all...

Nov 27, 2010 | 1998 GMC Sierra

1 Answer

MAF Low Voltage Cam shaft sensor at -45 degrees and trouble with transmission shifting properly was told was all related

Yes and no.....change the CamShaft position sensor first and it may clear the other problems

Aug 07, 2010 | 1997 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides