Question about 1986 Oldsmobile Cutlass Supreme

1 Answer

I have an 1986 olds cutlass supreme. I need to install the rear window molding trim that goes just over the trunk lid (side trim and roof trim are already installed with clips). Do i need special clips to hold it down? How do I install this rear window trim part?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

Yes you need the correct clips and it's real hard to install the bottom rail if the top and side rails are already on since the sides go over the bottom and the top goes over the sides to keep it from leaking.

Posted on May 26, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: Belt Placement on 1986 Oldsmobile Cutlass

for the most part there is a diagram under the hood showing you how the belt goes on try this website www.autozone.com to see if they have your car listed

Posted on Apr 24, 2009

c17hydro
  • 2984 Answers

SOURCE: how do I remove rear brake pads on 94 olds cutlass

Please don't forget to rate! This helps us help you!

1993–96 Vehicles

  1. Remove about 2⁄3 of the brake fluid from the reservoir with a clean syringe or baster type utensil.
  2. Raise and safely support the vehicle.
  3. Matchmark the relationship of the wheel to the axle flange. Remove the wheel and tire assembly.
  4. Reinstall two lug nuts to retain the rotor.
  5. Unfasten the bolt and washer attaching the cable support bracket to the caliper body assembly. It is not necessary to disconnect the parking brake cable from the caliper parking brake lever or disconnect the brake hose unless the caliper is to be completely removed from the vehicle. Freeing the cable support bracket allows enough flexibility in the cable to pivot the caliper up and down and remove the shoe and lining.
  6. Remove the sleeve bolt.
  7. Pivot the caliper body assembly up. Do not completely remove the caliper assembly body.
  8. Remove the outboard and inboard shoe and linings (pads) from the caliper support.
  9. Remove the two pad clips from the caliper support. To install:
  10. Bottom the piston assembly into the caliper bore. Use a suitable spanner-type tool in the piston slot to turn the piston assembly and thread it into the caliper body assembly.
  11. After bottoming the piston, lift the inner edge of the boot next to the piston assembly and press out any trapped air. The boot must lie flat. Make sure the slots in the end of the piston are positioned correctly before pivoting the caliper body assembly down over the shoe and lining in the caliper support. Use a suitable spanner-type tool in the piston slots to turn the piston as necessary. NOTE: Whenever installing new pads, install new pad clips. These should be provided in the disc pad kit.
  12. Install the two pad clips in the caliper support.
  13. Install the outboard and inboard shoe and lining in the caliper support. The wear sensor is on the outboard pad. The sensor is positioned downward at the leading edge of the rotor during forward wheel rotation. Hold the metal shoe edge against the spring end of the clips in the caliper support. Push the shoe in toward the hub, bending the spring ends slightly, and engage the shoe notches with the support abutments.
  14. Pivot the caliper body assembly down over the shoe and lining assembly. Be careful not to damage the piston boot on the inboard. Compress the sleeve boot by hand as the caliper body moves into position to prevent boot damage.
  15. After the caliper body is in position, recheck the installation of the pad clips. If necessary, use a small prytool to re-seat or center the pad clips on the support abutments.
  16. Install the sleeve bolt and tighten to 20 ft. lbs. (27 Nm).
  17. Install the cable support bracket (with the cable attached) with the bolt and washer. Tighten the bolt to 32 ft. lbs. (43 Nm).
  18. Remove the two lug nuts retaining the rotor.
  19. Install the wheel and tire assembly, aligning the marks made during removal.
  20. Carefully lower the vehicle, then firmly depress the brake pedal 3 times to seat the pads against the rotors.

Posted on Jul 15, 2009

  • 1 Answer

SOURCE: I need to know how to put rear struts on a 96 olds

I just had to do this to my cutlass supreme. It is fairly easy. First, you need to jack the car up in the rear (but dont forget to put wheel chocks in front of the front wheels to prevent any chance of rolling, and break all of the lug nuts loose while the car is still on the ground, and put jack stands under it to keep the car raised safely) and remove the rear wheels. Then look at where the strut mounts to the wheel, there are two bolts holding it on the wheel assembly; remove those (you may need to jack ut the suspension to remove the bolts). Now locate the two smaller bolts to each side of the the strut itself on the strut mount, holding it to the car (this is located at the very top of the wheel well) and remove them. Now u can compress the strut by hand and wiggle it free from the car. Once u have the old strut out, remove the large nut that is securing the strut to the mount. In some cases this is impossible to do due to the rust that has binded them together. If this happens, you will need to purchase a new strut mount for your new strut. AutoZone seems to be the cheepest place for parts. To install the new struts just do everything backwards. When the new struts are installed, the wheels may be slanted down. If this is the case, do not worry, they just need time to "relax" or be broken in. I hope everything goes smoothly and i wish you luck.

Posted on Jan 25, 2010

  • 2002 Answers

SOURCE: need to change fuel filter on 1986 cutlass supreme

You'll find it in the carburator. Unhook the fuel feed line from the front of the carb and undo the large nut directly where the fuel line connects to. The filter is there.Pay attention to how the filter comes out and put the new one back in the same way. Hope this helps.

Posted on Mar 22, 2010

arauzvictor1
  • 466 Answers

SOURCE: 1986 Oldsmobile Cutlass Supreme vacuum hose

Ok sent you this the engine you have to specify that engine has to help you. Thanks2c36ea6.jpg

Posted on Mar 24, 2010

Testimonial: "good job getting info. and real quick too"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

2 Answers

How to install replacement sunroof motor on a 1999 Pontiac grand prix


Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover


?€¢
J 2772-C Headliner Installer

  1. Remove the sunshades. Refer to Sunshade Replacement .
  2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
  3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
  4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
  5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
  6. Remove the dome light, if equipped.
  7. Remove the coat hooks. Refer to Coat Hook Replacement .
  8. Remove the assist handles. Assist Strap Replacement
  9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
  10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
  11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
  12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
  13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
  14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

Feb 27, 2015 | 1999 Pontiac Grand Prix

2 Answers

Bentley Boot lid manual release


This is all the Bentley shows:

doorlockswitch1.gif
Location: Driver's side door trim in storage compartment.

Removing:

- Remove driver's side door trim:
Repair Manual, Body Interior, Repair Group 70 - Unplug connectors.


doorlockswitch2.gif
Carefully disengage catches -arrows-.
- Press switch for interior monitoring and towing protection -1- or trunk release switch -2- out of trim toward rear.

Installing

Installation is carried out in the reverse order.


doorlockswitch3.gif
Remove trunk lid lock.

Repair Manual, Body Exterior, Repair Group 55
- Use a flat screwdriver to pry plastic tab -3- off retaining pins -1-.
- Bend plastic tab fully to rear.
- Pull contact switch -2- first sideways and then up and out of trunk lid lock.

Installing

Install in reverse order, paying attention to the following:

Note:

Make sure that washers are correctly seated between plastic tab and trunk lid lock.

Sep 01, 2012 | Bentley Continental Flying Spur Cars &...

1 Answer

My rear defrost on my 1986 cutlass supreme is not working. i checked all the fuses and they are all working.


there is a repair kit at the parts store for these "broken lines" in the window - around $11.00 - either you you have a broken wires in the glass or wires leading the power into it,. check the power at the terminal connection along side the window first to be sure..
Best regards
Ck

Mar 06, 2011 | 1986 Oldsmobile Cutlass Supreme

1 Answer

I have a 1999 chevy blazer I cannot close the


The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass
  1. Close the sunroof and open the sunshade.
  2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
  3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
  4. Remove the glass from the vehicle.
To install:
  1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
  2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
  3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
  4. Check the operation and fit of the glass.

Motor
  1. Disconnect the negative battery cable.
  2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
  3. Remove the headlines as follows:
    1. If equipped, remove the overhead or sunroof console.
    2. If equipped, remove the dome lamp.
    3. Remove the coat hooks and the assist handles.
    4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
    5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
    6. On four door models, remove the body lock pillar trim panels.
    7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
    8. On two door models, remove the rear seat upper seat belt anchor bolts.
    9. Remove the upper and lower front seat belt anchor bolts.
    10. Remove the rear seat belt lower anchor nut (two door models only).
    11. Remove the end gate or liftgate opening sill plate.
    12. Remove the jack storage cover (left side).
    13. Remove the upper body side trim panel screw (left side).
    14. Remove the upper body side trim panel and the body side front lower trim panel.
    15. Remove the headliner from the vehicle.
  4. Remove the sunroof console mounting bracket.
  5. Remove the straps that retain the wiring harness.
  6. Tag and unplug any necessary electrical connections.
  7. Unfasten the screws that attach the motor to the sunroof assembly.
  8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
To install:
  1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
  2. Attach all electrical connections that were unplugged.
  3. Attach the straps that retain the wiring harness.
  4. Install the sunroof console mounting bracket.
New headliners must be pierced to accommodate actual vehicle accessories.
  1. Install the headliner as follows:
    1. Install the body side front lower trim panel and the upper body side trim panel.
    2. Install the upper body side trim panel screw (left side).
    3. Install the jack storage cover (left side).
    4. Install the end gate or liftgate opening sill plate.
    5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
    6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
    9. On four door models, install the body lock pillar trim panels.
    10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
    11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
    12. Install the coat hooks and the assist handles.
    13. If equipped, install the dome lamp.
    14. If equipped, install the overhead or sunroof console.
  2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

Jun 03, 2010 | 1999 Chevrolet Blazer

1 Answer

Belt Placement on 1986 Oldsmobile Cutlass


for the most part there is a diagram under the hood showing you how the belt goes on try this website www.autozone.com to see if they have your car listed

Apr 24, 2009 | 1986 Oldsmobile Cutlass Supreme

1 Answer

Choke is stuck in 86 olds cutlass supreme chugs and doesnt go


Choke coil & adjustment should be on side of carburetor.

Nov 27, 2008 | 1986 Oldsmobile Cutlass Supreme

2 Answers

There is a water leak somewhere in my 98 toyota camry that leaks into my passenger side floor. There is no sun roof and no visible leaks from the windows or doors. Any thoughts? A/C leak maybe? water...


I am the original owner of camry xle 1998 with wet floors. In 2000 I had drivers side door seal leaking at welt. Removed old door seal and new weather strip on drivers side installed. The door panel was never wet, but wet at bottom of door where there are drain holes...slowly leaking under carpet.
In 2001 later water again. Coming from overflowing A/C evaporator-drain plugged/ tank full of debris. Removed evaporator, cleaned + drain cleaned.
In 2003, driver door seal against window rotted. Removed door panel and found leak at window belt molding at the mirror joint inside + out. Lots of mold under carpet needed to replace! Made a fuss at dealers for reacurring problem and they replaced the carpet for free.

Sep 07, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...