Question about 1988 Mitsubishi Cargo

1 Answer

Canter window wont wind up

The front roller on mechanism has dropped out of the track-how do I get it back in? any new parts needed?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Mitsubishi Master
  • 51,269 Answers

This happens if the window goes down too far because the stop has moved or broken off. Try refitting it as there should ne no parts necessary as the rollers are either "v" shaped or will run in a track. Make sure the window glass channels are correctly adjusted after fitting the roller back in and check for max down position

Posted on May 14, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to replace drivers side window on 95 chevy truck

Remove interior door trim. There will be screws as well as plastic pins that have to be pried out. Wind the window all the way down. There will be some tracks in the lift mechanism with rollers that are attached to the window frame. Locate and remove the bolts that secure the frame. The window should then come out.

Mar 05, 2015 | Cars & Trucks

1 Answer

How do I fix front window came off roller can't wind up

Door card will need removal and possibly a new door window mech as the window runs up and down a runner by a cable and either motor or winder. Sometimes you can put them back in but more often than not something has broken.

Oct 15, 2014 | Cars & Trucks

1 Answer

I have a 2003 GMC Sierra 1500 with crank windows. My passenger window rolls down only about 1 inch. Feels bound up. Took panel off. Can't really see what is going on in there. Cables are tight, good...

Is the 1-inch gap uniform from front to back of the window, or is it greater at one end or the other? The window regulator (a scissors-like assembly inside the door) usually has two criss-crossing arms mounted to either end of the window. There are nylon rollers that move within a small track where the regulator arms mount to the window. Sometimes, these rollers break or become loose and jam in the small tracks. Remove the panel again and look at where the window is attached to the regulator. Likely there are screws or bolts going through the tracks and pre-drilled holes in the bottom of the window. You can try removing these fasteners, lifting the window out completely, and operating the crank. Observe the regulator for proper operation, and if jamming occurs, look at those nylon rollers. Good luck.

Sep 29, 2013 | GMC Sierra 1500 Cars & Trucks

2 Answers

The front passenger window in my 2004 freelander has dropped how do I fix it.

pull out the door panel and put it back on the track just the window up and then slid it back on the track and tighten the bolts on the track : )

Jan 15, 2013 | 2004 Land Rover FreeLander

2 Answers

My thing broke that makes my drivers front window wind up even. what part do i need? Ihave power windows.

There is a plastic stay clip that attaches to that hole that guides the window in the track

May 08, 2012 | 1994 Oldsmobile Cutlass Ciera

1 Answer

My window i thought came off track however when i got my panel off a little white piece was broken and my window wont stay up

That white peice could have possibly been on of the rollers from the regulator or a guide.
Sometimes you can purchse a new roller and it will need some pressure to snap it onto the pin. Or you can purchase a repair part that is the roller already on a pin and the old pin needs to be ground off from the back side (its like a rivet smashed onto the regulator or guide).
Then that white piece could have came from something else. Don't really know unless you look.

Aug 30, 2011 | 2000 Pontiac Grand Am GT

1 Answer

The nearside front window is stuck down and will not wind back up

Not sure if its power windows or manual windows, you said wind so its gotta be manual, remove the door panel and make sure nothing fell apart and jammed the track, if nothing is found then the track may be broken,

Sep 01, 2010 | Renault Sportwagon Cars & Trucks

1 Answer

Three out of four windows ''came off track'' on my 1998 expedition. I was told that the ''pklastic clip must have broke'',. How do I repair this?

You will need to remove the door panels to access the lift mechanism. The mechanism looks like the ends of the arms, they have a roller that snaps into the track mounted to the bottom of the door glass. Most larger parts stores carry the replacent rollers and clips under the brand name "Help".

Jun 30, 2009 | 1998 Ford Expedition

1 Answer

2005 Lesabre windows, front and rear off track.

First you would need to remove both door trims to inspect. You might encounter a broken roller or a roller off off the track. Until then, can't tell you much more.

Mar 31, 2009 | 2005 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides