Question about Chevrolet Cavalier

Open Question

How do i bleed clutch on Nissan Dualis 08

I installed new clutch on 2008 Nissan dualis with slave cylinder I need to know how to bleed it thanks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

  • 101 Answers

SOURCE: How do I bleed the clutch slave cylinder on my 2005 VW Jetta 2.5L

the clutch and brake resevoir are all in one.

Posted on Aug 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I bleed a 2008 Nissan X Trail 6-speed dual clutch?


if it has an external slave cylinder , bleed it at the bleed screw
If it has a composite slave cylinder( one that is inside the bell housing) there will be a bleed screw attached to the outside of the housing on on the end of a hose on the outside of the bell housing.
either way bleeding process is the same for an external slave cylinder.

May 14, 2015 | Nissan Cars & Trucks

1 Answer

How do I replace the rear wheel bearing in a 2010 Nissan dualis


Not sure on the Dualis, but Nissan usually has four bolts holding hub/bearing assembly on from the backside. If you have rear disc brakes and the parking brake shoes are inside the hub/rotor, this needs to be removed to access it. Hope this helps

Apr 21, 2015 | Nissan Cars & Trucks

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

I have a 1992 nissan 300zx and i just installed a new clutch master cylinder and a new clutch slave. i'm tring to get the pedal to get firm so i can bleed it and get a full pedal,but when the pedal gets a...


you need to bleed the cluch slave cylinder located on the transmission and the clutch operating cylinder located in the passenger front hood compartment next to the power steering resivoir

Mar 30, 2010 | 1992 Nissan 300ZX

2 Answers

Clutch pedal going to the floor too easily..


You likely have a leak in either the master for the clutch, the line going to the slave unit or the slave itself. You need to look at these items and replace any leaking components. If the master is full, likely it is internally bypassing and therefore needs replacement. Air in the system can only get in there from a leak. bleeding may make it work for a short time but is not a cure. After making any repairs you do need to bleed it though. (just like brakes)

Oct 23, 2009 | 2004 Nissan Maxima

2 Answers

I need to bleed my clutch in my 89 nissan pickup


if you have just instaled a new clutch you need to make sure the clutch disk has not ben instaled back wards and all the bolts holding the pressure plate are torqued evenly if eather is not corect the slave cyl will extend but not relace the clutch, if you have some one step on the clutch and it moves 1 to 2 in the problem is in the pressure plate or clutch disk,

Jul 06, 2009 | 1987 Nissan 300ZX

2 Answers

Nissan Sentra won't move.


Most likly needs a new clutch. but before you do that make shore the clutch slave cylinder is releasing.Do this by opening the bleed screw on the clutch slave cylinder. If there is preasure released when you do his you may have a stuck master cylinder. Not likly but worth the trouble to try

Jun 29, 2009 | 2001 Nissan Sentra

2 Answers

How do I bleed the master clutch cylinder


Drain or bleed? The bleeder nipple is on the slave cylinder. Fill master cylinder,leave the cap loose, open the bleed nipple at the slave cylinder,and let gravity do the rest. whe vo more aie bibbles come out and it drips steady. Close the bleeder, top of the master cylinder and you are done.

May 30, 2009 | 1996 Nissan Maxima

1 Answer

300Zx will not shift out of 5th gear


is there any pedal pressure when you step on the clutch? I had a similiar problem with my 91 300zx tt....it was stuck in third gear, no pedal pressure on the clutch whatsoever....i had cracked the pivot ball and the clutch slave 'popped out'. i had to pull the trans to fx the problem because i could not reattach the clutch fork onto the release bearing with the trans in the vehicle....you need to bleed the system...gravity bleed the slave until there are no air bubbles. make sure you top off the clutch master cylinder in the process.....then bleed the clutch operating cylinder.....it is in the passenger front hood near the power steering resivoir....top off the clutch master cylinder again. i hope this helps.

Apr 03, 2009 | 1990 Nissan 300ZX

1 Answer

The clutch on my car stuck to the floor. I check the reservoir was completely empty. I have a feeling the slave cylinder is filled with air. I'll need to get the schematics to see how to bleed the clutch.


Bleeding the clutch is similar to bleeding brakes. You'd pump the clutch pedal several times to get the pressure up, and then open the bleeder on the slave cylinder (mounted down on the transmission). Repeat and add fluid as needed until no air comes out.

Two things - first off, some cars have more than one bleed point (the Nissan 300ZX is one of those), so be sure there is only the slave cylinder to bleed. Second, if it went right to the floor, something failed - either the slave cylinder or the master cylinder. Changing the slave is relatively easy - usually two bolts and it comes off, you put on a new one, and bleed it as described above. Often the slave cylinder is less than $30, so it's worth it to try changing it if you can't get the pedal to come back off the floor on its own. A clutch master is significantly more expensive and more difficult to change, so start cheap and easy and replace the slave cylinder if you can't pump the pedal to get pressure built up for a bleed.

Jul 23, 2008 | Chevrolet Cavalier Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...