Question about 1988 Lincoln Mark VII

2 Answers

I have hard breaks on my 1988 lincoln mark vii and my abs light stays on any help

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Filmmaker:

    Uploaded 5 video answers.

  • Lincoln Expert
  • 95 Answers

LEARNING ABOUT YOUR BRAKE SYSTEM
The hydraulic brake booster on a late model Mark VII and early Continentals, is very different from most. It is equipped with something known as a "TEVES" brake system. I'll attempt to teach you what does what and why, so you won't spend a ton of money just because you and maybe your mechanic aren't familiar how it works. The way its always been is,..."if you don't understand it...replace the whole thing"! The problem with using this technique is, unless you want to spend $2K for the whole thing, your going to be buying a used system....which may not be a whole lot better than the one you have now.
The main parts in the system that we will discuss include an ACCUMULATOR, a HYDRAULIC PUMP, a hydraulic pump RELAY, and a PRESSURE SWITCH. These are the key players in this operation.

THE LOCATION OF THESE PARTS ARE AS FOLLOWS:
HYDRAULIC PUMP MOTOR= Underneath the brake assembly (2 pin connector) Hydraulic pump motor
RELAY = On the drivers side strut tower
PRESSURE SWITCH = 5 pin connector facing the # 7 or 8 spark plug(drivers side)
ACCUMULATOR = Round black ball on the drivers side

WHAT THESE ITEMS DO:
HYDRAULIC PUMP MOTOR is an electric hydraulic pump used to "boost" pressure for the brake assembly. This pump is $900 new!
hydraulic pump motor RELAY is just what its sounds like. It gives the hydraulic pump motor power to come on.
PRESSURE SWITCH is the "brains" in the system. It senses how much pressure is "on line", and when the system needs more pressure, it tells the relay to "power up" the hydraulic pump motor.
Another one of its jobs is to turn on the RED BRAKE LIGHT, then the ANTI-LOCK lights to alert the driver that the pressure is dangerously low. (The reason the anti-lock light comes on, is because the ABS cannot fuction if theres a problem with the manual brakes)
ACCUMULATOR stores energy or pressure like a reservoir. Its there so the hydraulic pump motor only has to come on every 3rd or 5th time. Its design is more complicated, but basicaly the same principle as an air tank on a compressor.

WHAT NORMALLY HAPPENS:
Whats usually happens is, in time, the accumulator gets weak with age and can't hold the pressure like it was designed too, and therefore, the hydraulic motor comes on everytime the brakes are applied....rather than every 3rd or 5th time. This means all these parts are working 3 or 5 times more than they were designed to. This puts an extreme amount of pressure on an already old system.
What we know from this is, the accumulator needs replacement because its what started all this, but now the pressure switch and relay needs replacement also because it has worked it to *****.
NOTE: always replace the relay when replacing the pressure switch. The relay came on everytime the pressure switch told it too, so if ones worn out....the others not far behind!

Posted on May 07, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Lincoln Master
  • 808 Answers

Bad vacuum brake booster test booster by shutting car off and don not touch pedal open hood and remove hose to booster a wooosh sound should be heard if not need a booster.

Posted on May 13, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1169 Answers

SOURCE: Dashboard removal, 1988 LINCOLN, MARK VII

If you have never done this before, you really need to go get a Haynes or Chilton manual for this. They run about $25.00 and have step by step plus pictures. I've done one in my carreer and will never do another. And it was for my son. Believe me, it's a task I don't wish on anyone.
Go check out a manual. Google "Haynes Repair Manuals". It's worth it.

Posted on Mar 15, 2009

  • 60 Answers

SOURCE: Can I put a Ford 460 engine into my 1988 Lincoln Mark VII?

Technically it will fit, if you dont like having a hood. But again. Stick with the trusty 302, Toss a Novi 1000 on it, and enjoy.

Posted on Aug 18, 2009

  • 1 Answer

SOURCE: 1988 Lincoln Mark VII (Bill

I also had the same problem, had to switch back to Motor Craft voltage regulator with the Bill Blass model Mark VII.

Posted on Oct 05, 2009

CMV9
  • 594 Answers

SOURCE: abs brake light on

actually you may not need to replace any parts. from what you are explaining on the vehicle you have a air lock in your brake lines. try and bleed the brakes again starting from the rear passenger than the drivers passenger than the passengers front and last the drivers front. than disconnect the negative battery cable for about 5 min to reset the lights and see what happens. please let me know if you need more assistance with this problem.
please do not forget to rate and comment about your expereince with fixya today.

Posted on Dec 27, 2009

emissionwiz
  • 76846 Answers

SOURCE: How do I change a 1986 Lincoln Mark VII ABS brake

just disconnect the ABS control module, the system will then default to standard brakes, you will however have a ABS warning light on all the time.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard Brake Pedal with ABS and Brake Light on


Sounds like the power brake unit has failed.

May 11, 2016 | 1987 Lincoln Mark VII

1 Answer

1992 Lincoln Mark vii speedometer not accurate


Output shaft speed sensor problem.

Lincoln Mark VII Maintenance & Repair Questions - CarGurus

www.cargurus.com > Questions > Lincoln > Mark VII
CarGurusJohnny asked a 1988 Lincoln Mark VII LSC Maintenance & Repair question about a ...nicolse7 asked a 1992 Lincoln Mark VII Maintenance & Repair question ...

Sep 08, 2015 | 1992 Lincoln Mark VII

2 Answers

1988 lincoln mark vii abs light stays on and i have hard breaks


ABS sensor in the brake hubs are bad, get a brake job.

May 13, 2014 | 1988 Lincoln Mark VII

1 Answer

Fuse box diagram 1992 Lincoln Mark VII


On this website (link below) you find fuse box diagram and description for Lincoln Mark VII (1988 - 1992)

Lincoln Mark VII 1988 1992 fuse box diagram Auto Genius

Dec 18, 2011 | 1992 Lincoln Mark VII

2 Answers

1988 Lincoln Mark VII, Bill Blass, My abs system has seemed to stop working, doesnt want to allow the breaks to stay pumped up... when car is running brakes are gone completely... ive replaced the rotors,...


I have not heard of an ABS causing these problems. Usually, a loss of pressure is a hole in a brakeline or a bad master cylinder.

The first brakelines to leak on my 1988 Bill Blass where those going under the engine. Check in the frame where the lines are routed from the ABS to the front brakes.

I use a Vacuum Handpump Bleeder. As long as there is fluid in the Master, you should eliminate the air. If you have a leak when you draw down each wheel you may hear a whistling, deflating ballonlike sound of the air draw. My handpump has a gauge which will show a pressure drop.

Or you can go the other direction and disconnect the ABS lines to the wheels. When you draw the vacuum from the closed Calipers, there should be little air in the lines. However, a hole in the line will continue to drop the draw from that particular wheel Caliper. This would prove you have an opening in the line.

Oct 10, 2010 | 1991 Lincoln Mark VII

1 Answer

How do I change a 1986 Lincoln Mark VII ABS brake system over to a standard or power brake system where do I buy the parts..


just disconnect the ABS control module, the system will then default to standard brakes, you will however have a ABS warning light on all the time.

Feb 06, 2010 | 1990 Lincoln Mark VII

2 Answers

CAN I REPLACE AN ABS POWER BOSTER &MASTER CYLINDERWITH A NEW NON ABS PAIRON MY 88 LSC


yes you can using a brake booster and master cylinder from a 1984-86.5 Mustang SVO Try searching some of the lincoln forums

Jun 25, 2009 | 1988 Lincoln Mark VII

2 Answers

Can I put a Ford 460 engine into my 1988 Lincoln Mark VII?


Technically it will fit, if you dont like having a hood. But again. Stick with the trusty 302, Toss a Novi 1000 on it, and enjoy.

Apr 26, 2009 | 1988 Lincoln Mark VII

Not finding what you are looking for?
Cars & Trucks Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...