Question about 2001 Ford F150 Styleside SuperCrew

Open Question

F150 2001 outside mirror

How to replace

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 gmc heated mirror module


Could have a DDS an PDS .depends on what RPO code yours has >
Outside Mirror Description and Operation (with RPO DL3)
Or
Outside Mirror Description and Operation (without RPO DL3)
Without
Heated Outside Rearview Mirror Operation
The REAR DEFOG relay controls the operation of the heated outside rearview mirrors. When rear window defogging is requested, the REAR DEFOG relay is energized and B+ is applied to the supply voltage circuit of the mirror heater element, located in the mirror face. A constant ground is also applied to the mirror face. Current will pass through the mirror heater element, warming the mirror, so long as the rear window defogger is commanded ON.

With
Heated Outside Rearview Mirror
The DDS and PDS control the activation of the mirror heaters. Upon receiving a serial data message indicating a request for heated mirrors, the DDS and PDS, will apply voltage to the mirror heater element supply voltage circuit. The mirror heaters will remain active until a new message is received indicating rear defogger is to be deactivated.
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a four position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a three position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Mirror Extend/Retract Switch--Integrated into DDS and is a two position switch that allows the operator to select the mirror extend or mirror retract position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Folding Mirror Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Your best bet mite be to take to a qualified repair shop , i really don't think you'll be able to do anything with it.
Do you have wiring diagrams so you know which wires to test ,do you know how to do electrical testing ?
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.

Sep 15, 2017 | 2007 GMC Sierra 2500HD

1 Answer

I have a broken side mirror on my 2009 Honda Pilot and need to replace it how do i remore the side mirror? Not the glass the whole thing.


You're lucky with this one, you do not have to remove the door panel to get the outside rear view mirror off.

Here's how do replace it: go here! just type this in search box,on pc. 2009 honda pilot outside mirror replacement. then click on first link, good-day !

Sep 20, 2011 | 2009 Honda Pilot

1 Answer

Replace passenger mirror


glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.
  1. Remove the front door trim panel; refer to Section 501-05.
  1. Remove the outside rear view mirror access water shield.
    gn1881a.gif
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect and remove the speaker.
    gn1882a.gif
  1. Disconnect the outside rear view mirror electrical connector.
    gn1883a.gif
  1. Remove the outside rear view mirror.
    1. Remove the nuts.
    1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.
    gn1884a.gif

Oct 26, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Cracked mirror only, mounting and other parts are functioning well. Can I purchase a mirror only and if so, where?? This is for 2006 Pontiac Grand Prix and the passenger side mirror is cracked but works...


Hello, yes the glass can be replaced. you will need to see your local GM dealer for the glass. real simple to replace.





  • Carefully push the outside rearview mirror face on the inner edge, near the front door window glass, to allow access.
  • Insert a large flat-bladed screwdriver in the slot between mirror lens and the mounting base.
  • Grasp the mirror face firmly and pull it from the mirror body.
  • Remove the outside rearview mirror case from the outside rearview mirror housing and disconnect the heater wire, if equipped.






  • Using the palm of your gloved hand, press firmly on the center of the glass until the case seats onto the motor.
  • The mirror will make a snapping noise when properly seated.
  • Inspect the mirror for proper operation.


  • cf49034.gif

    f845709.gif

    Jul 03, 2010 | 2006 Pontiac Grand Prix

    1 Answer

    Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


    here's 1996, all I have. Please rate.

    Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

    Removal
    1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




    1. Remove the wire clip.
    1. Disconnect the power outside rear view mirror electrical connector.




    1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




    Installation
    To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
    Removal and Installation
    Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
    Removal
    1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws.


      Remove the outside rear view mirror mounting hole cover.
    Installation
    To install, reverse the removal procedure. Mirror Control
    Removal
    1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


    May 13, 2010 | 1995 Mercury Villager

    1 Answer

    How do i replace left door mirior


    remove trim panel, remove mirror fasteners.

    Glass, Outside Mirror—Town Car

    Removal and Installation
    1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
    1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
    1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
    1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
    1. To install reverse Removal procedure.
    ------------------------------------------------------------
    Mirror, Power—Outside Rear View
    Town Car

    Removal and Installation
    1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    1. Remove front door trim panel (23942). Refer to Section 01-05 .
    Trim Panels, Door Front—Town Car
    Removal
    1. Snap out two door pull strap retaining screw covers. Remove screws.
    1. Remove three screws on front and rear side and center of front door trim panel (23942).
    1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

      Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
    1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

      Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
    1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
    1. Remove the door trim panel.
    1. Disconnect two electrical connectors.
    1. Remove nut from outside rear view mirror mounting base.
    1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
    1. Remove screw from outside rear view mirror base.
    1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
    1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

    Nov 05, 2009 | 1996 Lincoln Town Car

    1 Answer

    How do I remove the left side mirrer on my 2000 ford explorer?


    Mirror — Outside Rear View Removal
    NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.
    1. Disconnect the battery ground cable (14301).
    1. Remove the front door trim panel; refer to Section 501-05.
    1. Remove the speaker.
      1. Remove the screws.
      1. Disconnect the electrical connector.
      1. Remove the speaker.
      gk6980a.gif
    1. Remove the outside rear view mirror (17682).
      1. Disconnect the power mirror wiring clips.
      1. Remove the outside rear view mirror nuts.
      1. Remove the outside rear view mirror.
        • Feed the power mirror wiring through the opening in the front door (20124).
      gn0316a.gif
    Installation
    1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.
      gn0317a.gif

    May 29, 2009 | 2000 Ford Explorer

    1 Answer

    Eddie Bauer mirror replacements


    is it an aero mirror with no arms?
    Or a trailer tow mirror with arms?
    The glass is repalceable. It is mounted on a center post with a ball on it. The mirror has a socket on the back center.
    It also has 2 jack srews (plastic) that go into the tiny motors that move the mirror. You can push and pull on the glass and they will retchet, it won't hurt them.

    You have to pop the mirror off the ball.

    It helps to heat the socket with a hair dryer to put the new one on.
    Please rate as fixya if this solves your problem.

    Glass — Outside Rear View Mirror
    Removal
    1. Remove the mirror glass.
      1. Position the mirror glass to obtain a gap at the outside edge of the mirror.
      1. Carefully pry the outside edge of the glass away from the mirror housing.
    d6ec385.gif Disconnect the electrical connector

    987d3c2.gif
    Connect the electrical connector


    NOTE: Engage the center pivot before the four inserts.
    Install the mirror glass.
    • Engage the center pivot and the four inserts
    52f3cfa.gif

    Mar 10, 2009 | 1997 Ford Expedition

    1 Answer

    Kia sorento 55 plate wing mirror


    1. Disconnect the negative battery cable.
    2. Remove the outside rearview mirror garnish.
    3. Disconnect the harness connector.
    4. Remove the 3 bolts and the outside mirror.
    To install:
    1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
    2. Connect the wiring harness.
    3. Install the mirror garnish.
    4. Connect the negative battery cable

    Jan 31, 2009 | 2005 Kia Sorento

    1 Answer

    Replacing passenger side outside mirror


    open the door, on the opposite side of the mirror there is an interior panel, remove it, there are 3 nuts in there remove those, the mirror should come off, if it is power be sure to unplug it.

    Oct 07, 2008 | 1997 GMC Sonoma

    Not finding what you are looking for?
    2001 Ford F150 Styleside SuperCrew Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...