Question about 1988 Ford Bronco

1 Answer

How to replace an oil sending unit. 1988 ford bronco.2wheel dr. manual trans.2.9 liter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,982 Answers

R&R is generally not difficult but most require a special socket (depending upon design and whether for light or gauge)

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Explorer 5.0 liter V8, 2 wheel dr. Where is the oil sending unit?


it is located either a rear of intake by firewall or on the oil filter mounting housing at top. it is a single wire connector.

Jul 05, 2015 | Ford Cars & Trucks

1 Answer

How to get the right fuel pump relay for 1988 ford bronco 2 xlt can't see numbers on it. 4 wheel drive manual trans. 2.9 v/6 engine


Call the parts stores.

Call more than one to check prices.

Don't let them try to rip you off.

Nov 07, 2010 | 1988 Ford Bronco II

1 Answer

Blows black carbon out tail pipe n pulls back untill gas pedal is pushed to floor for 10 sec 1988 ford bronco 2 4x4 auto trans 2.9


Unfortunately there are several things that can be causing this issue. Try replacing your map sensor. They are relatively cheap and easily installed.

Nov 04, 2010 | 1988 Ford Bronco II

1 Answer

1988 ford bronco 4x4 fuil injection is the firing order the same as carb engin eng.302


1988 Ford Bronco Full Size 5.8 liter V-8 VIN "H"

a60a6d1.gif


Hope helps.

Jul 21, 2010 | 1988 Ford Bronco

1 Answer

I have an 1988 ford bronco 2 automatic V6 i pulled


There are shift solenoids in the transmission and apparently there's a problem them. I would get it to a trany shop and have it checked right away. If you continue to drive it you will ruin the transmission. Are sure you put the right computer in the vehicle? If you put a computer from a Bronco II with a manual trans in a vehicle with an automatic trans, the trans won't work right.

Jan 22, 2010 | 1988 Ford Bronco

1 Answer

I HAVE A 1988 FORD BRONCO WITH A 5.0 LITER ENGINE WITH WHAT IM TOLD IS AN AOD TRANSMISSION/ THE TRANS WILL NOT SHIFT INTO OVERDRIVE/ WHERE SHOULD I BEGIN MY DIAGNOSIS


line pressure test the overdrive drum see what the pressure is, it is very possible due to age the seal in the drum is worn out allowing it to slip.

Dec 15, 2009 | 1988 Ford Bronco

1 Answer

Transmission fluid leaking back, 1988 Ford Bronco


your output seal on the tranny or input seal on your transfer case is bad. you have to pull your transfer case to tell. this is a pretty straight forward job. block wheels. put transfer case in neutral. drop front and rear drive lines.diconnect transfer case shift linkage. there is a short commponent connecting the trans to the transfer case. the bolt on either end face each other. remove the bolts to the transmission. the transfer case is heavier than it looks, i suggest getting help. pull back on the transfer case until it will drop down. it will pull out a bit because of the trans output shaft. replace what will probibly turn out to be the tranny output shaft seal and reassemble in reverse order.

Nov 06, 2009 | 1988 Ford Bronco II

1 Answer

Oil sending unit leaks


"Motor" mount...shouldn't be anywhere near a motor mount! Should be near the distributor...or atop the intake manifold in the back of the engine near the firewall. This is a PAIN to replace, make sure the engine is cool...cause you HAVE TO climb inside the engine-bay to get to it. Make sure you teflon tape the threads of the new sending unit...
Good Luck
This is FULL SIZE Bronco description.

Jun 23, 2009 | 1988 Ford Bronco

1 Answer

88 bronco, oil gage is pegged at 0, goes normal later


v-8 engines it is right by the oil filter mounting pad

Mar 20, 2009 | 1988 Ford Bronco

4 Answers

Has no oil pressure when ideling, has 20 lbs at highway speed.


you have either a weak oil pump or a faulty sensor check the leads on the oil sending unit and make sure they are not frayed. if they are not take it off and have it bench tested if it passes replace oil pump...please rate this

Sep 03, 2008 | 1988 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...