Question about 1998 Dodge Ram 1500 4WD

2 Answers

Are the ball joints on a 1996 dodge ram 1500 4x2 pressed in? still has the OE on it.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

They are pressed in youll need a ball joint press to get them in or out can be rented at a rental place or some auto parts stores...

Posted on Sep 17, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Yes they are

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 dodge ram upper ball joint replacement


where did the replacement come from and did they give you the right one...repost

Feb 09, 2013 | 2004 Dodge Ram 1500

1 Answer

How do i replace ball joints on 1997 dodge ram 1500


jack up truck support truck remove brake caliper and support the caliper dont let it hang by the hose remove cotter pin from bottom of ball joint remove castle nut from ball joint use ball joint press to push ball joint up and out then use press to push in new ball joint make sure you grease them when you are finished both uper and lower press up and out.

Feb 02, 2010 | 2008 Dodge Ram 1500 2WD

1 Answer

1996 Dodge Ram 1500 2wd 318/ci


Use the balljoint removal tool to remove. Sometimes a bottle jack comes in handy for the stuck ones. When you put them back on, use a big C-Clamp

You can go to autozone.com and register for full free online repair manual for any vehicle if you ever need it.

Dec 13, 2009 | 1996 Dodge Ram 1500 Club Cab

2 Answers

Upper ball joint removal


I have a 98 dodge ram 4wd, and i am an auto mechanic. I replaced all 4 ball joints and both axle joints and did my front end alignment in about 4 hours. The ball joints are pressed into the front axle yoke holes. If you have a ball joint press tool (which i used) it works out pretty easily in a decent amount of time. Otherwise if your lucky, you could use a hammer, which is not nearly as easy. Also, sometimes depending on how long and rusted the front end is, you might have to heat up the area a little with a torch.I also recommend using the best ball joints you can afford, because it would **** to have to do it all again after another 10,000-60,000 miles.

Dec 01, 2009 | 1998 Dodge Ram 1500 4WD

3 Answers

How to change the ball joints on my 99 dodge ram 2500 4wd?


it takes a ball joint press which can be purchased at harbor freight. you should purchase "moog problem solvers". they are your best bet for trouble free repairs.

Nov 08, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Ball Joints


I highly recommend that you have a press available, they dont screw in unfortunatly.
To change uper ball joints; Remove tire Pull codder pin and remve nut Tap ball joint out of wheel/ brake assembly Remove upper control arm compleatly Use Press to push old ball joint out of controll arm.
A torch may be nessisary to heat controll arm. Press new ball joint all the way into controll arm Reinstall every thing Get a professional front end alignment. 

Good lcuk and hope this helps.

May 04, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

1997 DODGE RAM 1500


 just tare the axels down and pull the brake callipers and brake disks, to get to the ball joints. un bolt the nuts and take the peice holding the ball joints in and  then press out . But you need a ball joint press if you wanna do it on your own

Jan 06, 2009 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...