Question about 1999 Isuzu Rodeo

Open Question

Where is the camshaft position sensor located for a 1999 3.2L V6 Isuzu Rodeo?

A diagram would be very helpful.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

  • 163 Answers

SOURCE: 1998 ISUZU RODEO CODE READS P0121 THROTEL POSITION

Opposite side of your throttle cables into your intake...

Posted on Sep 25, 2009

stevenhurc
  • 450 Answers

SOURCE: where do i locate the

it is located on the inner rear section of the left hand head (left side of vehicle) under inlet manifold dont need to remove inlet manifold
and connector must face rearwards to work correctly


stevenhurc_4.jpg

Posted on Feb 04, 2011

  • 28 Answers

SOURCE: Where is the map sensor located on a 2004 isuzu

for all of you looking for the map sensor on a 3.5 it is under the top half of the intake so stop the truffel hunt

Posted on Jun 10, 2012

  • 141 Answers

SOURCE: location of camshaft sensor for 1999 isuzu rodeo

http://www.youtube.com/watch?v=m_uAnQFjTI4

Posted on Jul 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the crankshaft position sensor on a 2004 isuzu rodeo 3.5


2004 no vin code posted nor the 8th VIN digit for engine code
so answers get 10x harder, lacking that one fact. USA car?
Coin toss 1:
learn the real name of engine, first
6vE1, 4 cams, and last year has VVT, (not trivial that)
and has 2 Cam sensors. to make VVT happy,. dig?
weve answered this many times here, over and over
did the scan tool tell you its bad.?
its on the rear of both heads,

the post above is wrong, he shows the 6vd1w engine,
here just for fun, again i post all V6,s just for you, and others too lazy to search or learn engine REAL NAME.

ill do all 3 V6 engines now.

3de1f741-1946-4f53-9161-03418aaee9a6.jpg


32dohc-kak3wjrwg2pwaolcwur0ctxj-2-2.jpg


32sohc-kak3wjrwg2pwaolcwur0ctxj-2-3.jpg


6ve1-kak3wjrwg2pwaolcwur0ctxj-2-4.jpg


left96-kak3wjrwg2pwaolcwur0ctxj-2-5.jpg


vin2004-kak3wjrwg2pwaolcwur0ctxj-2-6.jpg

Mar 18, 2017 | Isuzu Cars & Trucks

1 Answer

Where is camshaft sensor located on 2004 isuzu rodeo V6 3.5ltr


SENSORS (plural)
3.5L 4 cam engine? 6ve1? it has a real name BTW.
known real names makes help more easy and 10x buying parts.
on the 4 cam there are 2 CMP sensors on rear of heads

here?

http://jeepdied.com/look/alien-stuff/Isuzu/head%20cam%20sensors/35cmp1&2-location.JPG


if scans say it's ok, then it's ok (if dead start?, crank for 5 full seconds,see DTC now? )
no symptoms stated,why?

lean that scan tools show history of DTC errors(if lucky)
and live errors
the live errors are what makes savvy diagnosis win.
use the scan tool and learn to use it,its not hard.

Feb 26, 2017 | 2004 Isuzu Rodeo

1 Answer

Where is the location of the camshaft sensor for 1995 Isuzu Trooper


no engine stated, 4 banger or v6 but same answer.
there is no such sensor until 1996
why not post the problem or a symptom
and ask for help.
like
wont' crank.
cranks but will not start.
starts and stalls.
starts, runs but misfires.
like that.
get a tuneup yet?> (crystal ball)
V6 (guessing yours)
if you meant crank sensor its on the right side of engine block center.

seen here, CKP "crank sensor"
if you look for a CMP on line you will find it
but its Bunk, it's not there, stores mix parts up. et cetra.
http://jeepdied.com/look/alien-stuff/Isuzu/head%20cam%20sensors/CMP-wonder.pdf


836e5646-c779-44fe-b203-3249404738be.jpg

Dec 20, 2016 | Isuzu Trooper Cars & Trucks

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

1 Answer

Where is the location of camshaft sensor 1998 isuzu trooper


if its diesel 4JX1 its in top cam belt cover cant miss it, sensor is very clearly visible.
if its petrol V6 (6VD1 or 6VE1) its in left head at rear behind inlet manifold
these pictures are for petrol V6, Jackaroo(Trooper) and Holden Rodeo are the same.

stevenhurc_21.jpg



stevenhurc_22.jpg

Apr 10, 2011 | 1998 Isuzu Trooper

1 Answer

Where do i locate the camshaft position sensor on 2004 isuzu rodeo v-6, 3.5lt.


it is located on the inner rear section of the left hand head (left side of vehicle) under inlet manifold dont need to remove inlet manifold
and connector must face rearwards to work correctly


stevenhurc_4.jpg

Feb 01, 2011 | 2004 Isuzu Rodeo

2 Answers

Where is the crank sensor located at on 1999 isuzu rodeo?


Where Is The Camshaft Position Sensor Located On A 1999 Isuzu Rodeo?

Jan 10, 2010 | 1999 Isuzu Rodeo

1 Answer

Replace timing belton 1995 isuzu 3.2 V6


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1995/make/isuzu/model/rodeo/1995_isuzu_rodeo_timing_belt_diagram_marks.htm

Nov 23, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...