Question about 1999 Isuzu Rodeo

Open Question

Where is a diagram for a camshaft position sensor?

3.2L 6 Cylinder

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wilsodfarm
  • 986 Answers

SOURCE: WHERE IS CAMSHAFT POSITION SENSOR ON 2000 RODEO

left front of the engine

Posted on Dec 10, 2009

stevenhurc
  • 450 Answers

SOURCE: where do i locate the

it is located on the inner rear section of the left hand head (left side of vehicle) under inlet manifold dont need to remove inlet manifold
and connector must face rearwards to work correctly


stevenhurc_4.jpg

Posted on Feb 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor on a 2012 jeep liberty 3.7L


same as all 3.7s
on the cam (its V6 so has 2 cams)
one left bank, one right bank

quote SM
The Camshaft Position Sensor (CMP) on the 3.7L 6-cylinder engine is bolted to the right-front side of the right cylinder
head.



37-einpkkqvi3s0rywpzqnhcogf-2-0.jpg

Mar 18, 2017 | Jeep Cars & Trucks

2 Answers

Diagram of where a camshaft sensor is on a dodge stratus 2.4L 4 cylinder


2003 model
not confirmed
crank angle sensor might be near the stater motor on the block


26233366-qzmmc3ihqjw1j4mumdlnccct-4-0.gif

26233366-qzmmc3ihqjw1j4mumdlnccct-4-2.gif

Jul 07, 2016 | Dodge Cars & Trucks

2 Answers

My truck sonoma gmc 2001 dont past the emission test


Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

2 Answers

Where is the camshaft position sensor for


They are located on each head if im not mistaken on the corner near the air intake boot that goes to air filter. The cylinder head close to the radiator is 2 4 6.

Sep 20, 2014 | 2000 Lexus ES 300

1 Answer

Where is the rear bank camshaft position sensor located on a 2004 Nissan Maxima DOHC 6 cylinder?


Both cam sensors are on the rear of the cylinder heads. They are located in the same place on each head. The only difference in the two sensors is one has a straight connector and the other has an angled connector because of other things that are in the way, (see diagram)


dttech_172.gif

Aug 22, 2011 | 2004 Nissan Maxima

2 Answers

Hi my 2006 cadillac cts has error codes po 300 303 305 343 347 368 392 and 496 can u tell me what they are or a website to find out thank u


P0300 is multiple engine misfire detected
P0303 is misfire in cylinder 3
P0305 is misfire in cylinder 5
P0343 is camshaft position sensor A (bank 1)
P0347 is camshaft position sensor A (bank 2)
P0368 is camshaft position sensor B (bank 1)
P0392 is camshaft position sensor B (bank2)
P0496 is EVAP Canister Purge System High Purge Flow

Jan 28, 2011 | 2006 Cadillac CTS

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

I need to find the camshaft position sensor on my 2003 nissan murano


Camshaft Position Sensors are located on the cylinder head according to the following: Camshaft, Bearings & Lifters Removal & Installation To Remove:
  1. Remove the engine from the vehicle.
  2. Remove the front suspension member, transaxle and transfer case (if equipped) from the engine.
  3. Mount the engine in a suitable engine stand.
  4. Remove the timing chains and rear timing chain case.
  5. Remove the camshaft position sensors from the cylinder heads.
  6. Remove the intake valve timing control solenoid valves. NOTE: Mark the camshafts, camshaft brackets, and bolts so they are placed in the original locations during installation.
  7. Loosen the camshaft bracket bolts in several steps using the order shown.
  8. Remove the intake and exhaust camshaft brackets and the camshafts. Camshaft bracket bolt removal sequence nissan-03-35-4624.gif

  9. Remove the valve lifters and the secondary timing chain tensioner with stopper pin attached if necessary.
NOTE: Stopper pin was installed when the secondary timing chain was removed.
To Install:
NOTE: Clean sealant from front camshaft bracket, bolts and bolt holes.
  1. Turn the crankshaft until No.1 piston is at TDC on the compression stroke. The crankshaft key should line up with the right bank center line as shown. Crankshaft keyway position nissan-03-35-4625.gif

  2. If removed, install the secondary timing chain tensioners and valve lifters in their original positions. NOTE: The intake camshaft has a drill mark on the edge of the sprocket mounting flange.
  3. Position the camshafts on the cylinder heads with the dowel pins as shown. Camshaft dowel pin positions nissan-03-35-4626.gif

  4. Apply silicone sealant to the front (No. 1) camshaft bracket as shown. Apply silicone sealant to the front (No. 1) camshaft bracket nissan-03-35-4627.gif

    Camshaft bracket bolt installation sequence nissan-03-35-4628.gif

  5. Install and tighten the camshaft brackets using the following steps in the sequence shown;
    • Step 1 (bolts 7 - 10) : 1 ft-lb (2 Nm)
    • Step 2 (bolts 1 - 6) : 1 ft-lb (2 Nm)
    • Step 3 (bolts 1 - 10): 4 ft-lbs (5.9 Nm)
    • Step 4 (bolts 1 - 6) : 8 ft-lbs (10.4 Nm)
    • Step 4 (bolts 7 - 10) : 7 ft-lbs (9.3 Nm)
  6. Wipe off excess sealant from bracket No. 1.
  7. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head. The specification is -0.0055 to 0.0055 in (-0.14 to 0.14 mm). Replace the camshaft and camshaft bracket if out of specification. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head nissan-03-35-4629.gif

  8. Install the IVT control solenoid valves with new gaskets.
  9. If removed, install the camshaft position sensor.
  10. Install the rear timing chain case and timing chains.
  11. Install the engine in the vehicle.
prev.gif next.gif

Jul 03, 2010 | 2003 Nissan Murano

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...