Question about Buick Cars & Trucks

1 Answer

Why did my Buick lock me out with both remotes in the car?

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Maybe it got mad at you for something you said about it.
Most likely you accidently hit the lock button while getting out of the car.

Posted on May 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program the keyless remote on a 2006 Buick LaCrosse


2006 Buick Rendezvous Remote Programming For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release in step 6.
3. Insert key into the ignition cylinder but do not turn it.
4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
6. Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.
8. Repeat step 7 if you are programming additional remotes.
9. Remove key from ignition to exit programming mode

Oct 28, 2017 | Buick Cars & Trucks

1 Answer

1997 buick lesabre limited will not enter remote programming mode...key in ignition door open insert jumper pin 4 to 8 does nothing... turning key on cycle the lock sequence 1 time but does not allow...


jump terminals 4 and8 close all doors turn ignition on door locks should cycle press and hold lock and unlock buttons on transmiter after a 30 sec delay door locks will lock and unlock disconect jumper

Sep 07, 2013 | 1997 Buick LeSabre

1 Answer

2000 buick century door locks not working with remotes


check your fuses most likely blew the fuse

Feb 28, 2013 | 2000 Buick Century

1 Answer

We have 2 remote key pads and replaced the batteries. Still not working. the 2 car keys will not open the doors. we never used keys to open the doors. Now we are totalling locked out of the car. Any...


TO SYNCHRONIZATION REMOTES WHEN REPLACING BATTERIES,STAND 5 FEET OF THE VECHICLE.PRESS REMOTE TRANSMITTER LOCK AND UNLOCK BUTTONS SIMULTANEOUSLY FOR 7 SECONDS.HORN SHOULD CHIRP TO CONFIRM SYNCHRONIZATION.

May 18, 2011 | 2002 Buick LeSabre

1 Answer

Buick rendezvous remote reciever in rear door


check for power to solenoid , repair wiring or replace solenoid (actuator)

Jun 27, 2010 | 2005 Buick Rendezvous

1 Answer

Buick regal door locks not working correct


YOUR RELAY OR RELAYS COULD BE FAULTY.

Sep 18, 2009 | 1998 Buick Regal

1 Answer

2002 Buick Century auto door unlock requires


It may be failing contacts in your remote; these are normally little carbon buttons that can either get fouled with contaminents or wear out if made too thin.
You may have to replace the remote to regain normal function. 

Mar 06, 2009 | 2002 Buick Century

1 Answer

Keyless remote not working


try these , maybe its the same directions .1.) turn key off . 2.) use a fused wire , maybe your new remote came with a short wire , under your driver side dash is a connector that looks like this >
0103ca7.gif
push 1 end of the wire into the A hole , and the other end into the G hole , the door locks should lock and unlock , 3.) press the unlock button on the new remote , the door locks should lock and unlock . 4.) repeat this procedure if you have another remote you want to register . 5.) now disconnect that jumper wire , and test the functionality of your remote(s) . see what that does for ya .

J5

Jan 22, 2009 | 1994 Buick Park Avenue

1 Answer

Setting up keyless remote entry with a new remote


1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release.

3. Insert and remove key from ignition 2 times. Do Not turn ignition.
4. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

5. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.

6. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.

7. Repeat step 6 if you are programming additional remotes.
8. Remove key from ignition to exit programming mode.

Dec 09, 2008 | 2002 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...