Question about 1994 Ford Crown Victoria

Open Question

How to remove oil pan 1994 crown victoria

4.6 litre motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: Trying to drop the oil

done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Posted on Apr 13, 2009

  • 10 Answers

SOURCE: The speedomter on my 1994 Crown Victoria has stopped working

most likely the speed cable broke.

Dave

Posted on Apr 20, 2009

  • 5501 Answers

SOURCE: 94 crown vic driver power window does not work can

The window regulator can be broke. Its made of plastic and they break often.

Posted on May 05, 2009

  • 14036 Answers

SOURCE: no oil pressure on my 03 crown victoria

KNOCKING NOISE IS NOT A GOOD SIGN.SOUND IF YOUR ENGINE OIL LEVEL IS CORRECT NOT LOW. SOUND LIKE OIL PUMP AND MAIN BEARING FAILURE.YOU NEED A REBUILT ENGINE OR OVER HAUL.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a oil pump on 2003 ford crown victoria fastest way and easy


The only way to do it ,
- remove engine oil pan
-remove engine head covers
-remove front pulley
- remove front engine cover
-remove timing chains

Jul 09, 2017 | 2003 Ford Crown Victoria

1 Answer

How do i replace the motor mounts on my 1994 crown


I can only forewarn you about several things to watch for in hope of providing you with something to prevent you from breaking something.
You must also consider loosening the transmission mounts to free up the entire drivetrain. There may be some clearance problems at the rear of the motor and the Radiator hoses may not stretch, nor may the fixed A/C lines to the front A/C cooler allow much travel space.
The oil pan is not a lifting point, nor is the crankshaft pulley. The exhaust system is not flexible either.
Your best bet is to look at the actual motor mount and see whether the mount is flush or has protruding studs. Flush shaped will be easier to handle. An 1/4 inch of clearance would allow you to slide parts through the opening.
You could still get another Expert to answer. I owned a 1994 Crown Vic and was underneath it many times, but never changed a motor mount on it.

Oct 02, 2014 | 1994 Ford Crown Victoria

1 Answer

I have a leak that appears to be right under the oil filter..It is not a oil pan gasket leak. What I need to know is????? Can you fix that type of problem without removing the oil from the oil pan.


IT SOUNDS LIKE THE FILTER MAYBE DOUBLE GASKETED...AND NO YOU WON'T HAVE TO DRAIN THE OIL JUST SPIN OFF THE FILTER AND CHECK TO SEE IF YOU HAVE A GASKET ON THE FILTER AS WELL AS THE HOUSING

Nov 08, 2012 | 1994 Ford Crown Victoria

1 Answer

1992 Ford Crown Victoria Oil Pan is leaking. Is this a major problem to replace? Fred


It is recommended that you lift out the engine before attempting to replace the oil pan. Once the engine is lifted you can remove the bolts, remove the pan, clean all the old gasket material.
Installation: Remove the rear main bearing cap oil seal Remove the timing cover oil seal Clean all the mating surfaces and seal grooves Install new oil pan front cover seals Install a new rear main bearing cap oil seal Install new oil pan side gaskets on the block Make sure the tabs of the front and rear seal fit properly as these are critical spots Attach the oil pan to the engine block and install the retaining bolts

Feb 23, 2011 | 1992 Ford Crown Victoria

2 Answers

Where is the oil pump on a 1993 Ford Crown Victoria


The oil pump is located in the bottom of the oil pan. The oil needs to be drained and then remove the pan.You will see the pickup up tube extending down nto the pan and held onto the block with two bolts. Hope this helps

Jan 19, 2011 | 1993 Ford Crown Victoria

1 Answer

93 crown victoria.leaking oil under the oil pump of the motor


The oil pump is in the pan you may be leeking oil from the oil sending unit next to the oil filter or the filter may be leeking . get under vehicle after safely securing it wipe off and figure out where it is leaking from if oil pan is rusted through replace oil pan. usually its the oil sending unit switch usually under 20 dollars for part and it screws on and off

Nov 21, 2010 | 1993 Ford Crown Victoria

2 Answers

Where is the starter


The starter is located near the oil pan to engine area, at the flywheel, Access from under the car.

Sep 21, 2009 | 1994 Ford Crown Victoria

2 Answers

Whats the engine oil capacity for a 1999 ford crown victoria


look in the manual it will tell u...otherwise just google it

Aug 06, 2009 | 1999 Ford Crown Victoria

1 Answer

Rusted out out oil pan on my 1993 ford crown victoria that leaks oil is there an recall on this part


no recall that i know of,those pans like to rust by the drain plug and on the sides

Apr 26, 2009 | 1994 Ford Crown Victoria

1 Answer

Il pan rusting and leaking


Drain the oil from the system. Next remove the oil pan and reinstall a new oil pan and new oil pan seal.

Apr 19, 2009 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...