Question about 2009 Jeep Wrangler

Open Question

How do I check 09 jeep wrangler codes - 2009 Jeep Wrangler

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: 2006 jeep wrangler check engine light came on it

There is a software update for the PCM that addresses this issue. TSB 18-028-06

Posted on Jun 08, 2009

Ad
  • 14585 Answers

SOURCE: getting condinsation on the inside

Some condensation is normal, especially if you drive short trips. What to watch for is coolant lose and check the oil to see if it has turned milkly on you. this would indicate that you have a blown head gasket. if this is the case do not drive the vehicle anymore, as this will cause more damage to the engine.

Posted on Dec 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thanks for the help !! Dose anyone know what code dOnE mean on a Jeep Wrangler ?


only reference os far is the wrangle has finished reading fault codes

join this free jeep wrangler forum

lots of good help and information there

Jeep Wrangler Forum Jeep Wrangler Owners Community

Oct 15, 2016 | Jeep Cars & Trucks

1 Answer

My check engine light came on on my 09 Jeep Wrangler I did the turn key 3 times and got a diagnostic code but I forgot what it was it happened so fast now when I try to do it again it just says done how...


Unhook the battery for a while to give the computer time to reset, maybe as much as 24 hours then try it again. Could be as simple as a bad seal on the gas cap.

Oct 28, 2014 | 2009 Jeep Wrangler

1 Answer

1995 Jeep Wrangler 4.0L.. It has OBD 1... check engine light is not on but there is a code stored in the ECU aquired by 3 key turns... The code is 55... What is this?


55 Completion of diagnostic code display

It just says that it completed the diagnostic check (get one everytime you start your vehicle)

Jun 03, 2011 | 1995 Jeep Wrangler

1 Answer

Getting condinsation on the inside of 09 jeep wrangler xl unlimited


Some condensation is normal, especially if you drive short trips. What to watch for is coolant lose and check the oil to see if it has turned milkly on you. this would indicate that you have a blown head gasket. if this is the case do not drive the vehicle anymore, as this will cause more damage to the engine.

Dec 27, 2010 | 2009 Jeep Wrangler

1 Answer

Where is the fill hole 6 speed manual tranny in my 09 wrangler and what type of fluid does it take


That information should be in your owners manual. I know that the manuals for the Cherokees I have owned have that kind of info in them. I found the below on a Jeep forum but I can not vouch for this information:

"The following products are MS-9224 compliant:
• Chrysler synchomesh fluid #4874464
• Penzoil Synchromesh Fluid #18106
• Quakerstate Synchromesh Fluid #59634
• GM synchromesh fluid #12345349
• GM synchromesh fluid 12345577
• Havoline MTX fluid #1874

Nov 03, 2009 | 2003 Jeep Wrangler

1 Answer

2009 Jeep Wrangler - 4WD shifter linkage (problem & solution)


They acually have an Rapid response for this. This should have been replaced before the car was even sold.

Oct 05, 2009 | 2009 Jeep Wrangler

1 Answer

Shaking stearing 2009jeep


Once you have slowed down or hit the brakes,does the problem reoccur when you speed back up?If so,there is a very good chance that the steering alignment has been put well and truly out.An alignment at the least.Get the steering etc,checked for bent rods and at the most a broken mount on the chassis.Hope this helps

Sep 13, 2009 | 2009 Jeep Wrangler

1 Answer

I have a 1988 jeep wrangler that won't idle.


1. check for vaccuum leaks.
2. check for a check engine code
3. check the throttle body/butterfly plate for carbon build up.

Sep 09, 2009 | 1988 Jeep Wrangler

1 Answer

2006 jeep wrangler check engine light came on it


There is a software update for the PCM that addresses this issue. TSB 18-028-06

Jun 08, 2009 | 2006 Jeep Wrangler

1 Answer

97 jeep wrangler 2.5 running lean


check fuel pressure and check exhaust for leaks. exhaust leaks caqn play with the o2 sensor readings

Sep 15, 2008 | 1997 Jeep Wrangler

Not finding what you are looking for?
2009 Jeep Wrangler Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...