Question about 2005 Kia Picanto 1.1

Open Question

Can you buy crankshaft sensor bracket - 2005 Kia Picanto 1.1

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Expedition 2001 crankshaft sensor location and installation


  • Located front of engine, close to crank pulley
  • press the helpful button and follow me on Fixya for more tips
  • Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.
  • Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioning compressor's pulley.
  • Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.
  • Pull the electrical connection off the crankshaft sensor.
  • Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.
  • Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.
  • Press the electrical connection onto the crankshaft sensor.
  • Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.
  • Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley. write up found @ehow

How to Replace the Crankshaft Sensor in Ford 150 eHow

Jan 28, 2016 | Ford Expedition Cars & Trucks

1 Answer

Position of cam shaft censor in the ford f150


nstructions
    • 1

      Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.

    • 2

      Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioningicon1.png compressor's pulley.

    • 3

      Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.

    • 4

      Pull the electrical connection off the crankshaft sensor.

    • 5

      Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.

    • 6

      Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.

    • 7

      Press the electrical connection onto the crankshaft sensor.

    • 8

      Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.

    • 9

      Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley.



Read more: How to Replace the Crankshaft Sensor in a Ford F-150 ' eHow.com http://www.ehow.com/how_6769823_replace-crankshaft-sensor-ford-f_150.html#ixzz2Ebai9Ftj

Dec 09, 2012 | 1998 Ford F150 Regular Cab

1 Answer

Were is the crankshaft sensor located at on 96 neon


  • It is located on the firewall side of the engine block, passenger side, under the power steering pump. Unplug the electrical connector on the crankshaft sensor by lifting the plastic lock tab and pulling it off.
  • 2Remove the 10 mm bolt that secures the sensor to the block, using a socket. The bolt is in the hold down bracket. Twist the sensor to ease removal.
  • 3Insert the new sensor after checking to make sure that the O-ring is installed to prevent oil leaks and the spacer that comes with the sensor did not fall off. Insert the sensor and give it a little twisting motion as it is installed. Align the hole in the hold down bracket and insert the 10 mm bolt and tighten with a socket. Plug in the electrical connector.
  • Oct 10, 2012 | 1996 Dodge Neon

    1 Answer

    How to change a crank position sensor on 2006 suzuki forenza


    5) Install the rear A/C mountingbracket. Tighten the rear A/C mounting bracket bolts to 35 Nm (26lb-ft).6) Install the A/C compressor. 7) Install the power steering pump. 8) Connect the negative battery cable.12_16_2011_6_00_05_pm.jpg
    If this helps, please say so! Thanks! :-)

    Dec 08, 2011 | 2006 Suzuki Forenza

    2 Answers

    Location crankshaft sensor 96c1500 5.7ci


    CRANKSHAFT POSITION SENSOR LOCATED NEXT TO THE STARTER.

    Sep 16, 2011 | 1996 Chevrolet C1500

    1 Answer

    Where's the cranck sensor located?


    Click the boxes with a red x in them to see diagram images. 5VZ-FE Engine
    1. Disconnect the crankshaft position sensor harness. Fig. 1: Exploded view of the crankshaft position sensor mounting 86824pa8.gif

    2. Remove the bolt retaining the sensor to the vehicle.
    3. To install, attach the sensor to the vehicle, tighten to 69 inch lbs. (8 Nm).
    2VZ-FE and 3VZ-FE Engines
    1. Remove the engine under cover.
    2. Remove the alternator.
    3. Unbolt the alternator bracket.
    4. Disconnect the crankshaft position sensor harness.
    5. Remove the bolts securing the sensor and the sensor. Discard the O-ring.
    6. When installing, apply a light coat of engine oil on the O-ring, install on the sensor tighten the bolts to 74 inch lbs. (9 Nm).
    1FZ-FE Engine
    1. Remove the engine under cover.
    2. Unbolt the sensor protector. Fig. 2: Exploded view of the 1FZ-FE crankshaft position sensor mounting 86824pb3.gif

    3. Disconnect the crankshaft position sensor bracket and harness.
    4. Remove the bolt, nuts and sensor.
    5. When installing, attach the sensor and tighten the bolt to 14 ft. lbs. (20 Nm) and the nuts to 78 inch lbs. (9 Nm).

    Jan 28, 2011 | 1989 Toyota 4Runner

    1 Answer

    Where is the crankshaft sensor on a v6 2000 chrystler sebring


    CRANKSHAFT POSITION SENSOR - 2.5L
    REMOVAL
    Remove speed control servo from driver's side strut tower.
    Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
    Pull crankshaft position sensor straight up out of the transaxle housing.
    (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
    INSTALLATION - ADJUSTABLE
    All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

    NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

    Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
    Connect crankshaft position sensor electrical connector to the wiring harness connector.
    Attach connector to heater tube bracket.
    Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

    May 22, 2010 | 1998 Chrysler Sebring

    1 Answer

    Were is the crankshaft sensor on my 2000 daewoo leganza


    To find the crankshaft sensor you will have to.
    Remove the power steering pump if equipped,
    Remove the a/c compressor,
    Remove the a/c compressor mounting bracket bolt.
    Remove the accessory mounting bracket.
    Once you pull the a/c bracket out of the car you will see the
    cranshaft position senor (CKP).
    Remove the one bolt that hold it in place.
    Gently rotate and remove.

    Sep 20, 2009 | 2000 Daewoo Leganza

    1 Answer

    Crankshaft Position Sensor


    the dual crankshaft position sensor is secured in an aluminum mounting bracket and bolted to the left side of the timing chain cover, partially behind the crankshaft balancer, hope this helps get back to me if you need mre help. please rate my fix as i strive to be the best

    Apr 29, 2009 | 1997 Buick LeSabre

    2 Answers

    How do you replace a crankshaft sensor for a 1997 olds Delta 88?


    There are two crankshaft sensors located at the edge of the harmonic balancer. That's the large wheel coming out of the engine, passenger side, the wheel that powers the serpentine belt. One sensor is the crankshaft position sensor and the other is... I forget... crankshaft angle sensor or something. I replaced both on my car. I don't know wich one is your problem. When you buy a sensor, get the one with the mounting bracket already attached. They had problems with the sensor getting damaged from being adjusted wrong. Having the bracket already attached gives you the right adjustment.

    Remove the serpentine belt. (It has a tensioner wheel. When that is moved, the belt becomes loose and can be removed.) With an 18 mm wrench, turn the crankshaft until one of the openings in the metal fin is at the sensor, giving a space where the sensor can be removed. One sensor is reachable from the top, but it is real hard to see. The other is reachable from underneath. My guess is, the lower one is you problem only because my lower one failed twice and the upper one only once. Your son has to crawl underneath, unhook the wire from the sensor, and unbolt the sensor mounting bracket. Put the new one in. Keep your fingers crossed.

    Dec 03, 2008 | 1987 Oldsmobile Delta 88

    Not finding what you are looking for?
    2005 Kia Picanto 1.1 Logo

    Related Topics:

    11 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7697 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...