Question about 2001 Chrysler Town & Country

2 Answers

Replace front blower motor on 2002 Town and Country van

Trying to replace the front blower motor on a 2002 Town and Country van, already replaced the resistor. How do I remove the front blower motor? Is there a hidden screw? I think I removed 4 or 5.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 14 Answers

Go to your local discount tool center and get a 1/4" square drive flex extension. There is an additional screw on the backside that is a royal pain to get out! Dont get just a swivel joint...That will not work! The extension I am talking about is kind of like a tightly wound spring with a male square drive on one end and a female on the other. Worked for me!

Posted on May 13, 2014

  • Joseph Gauthier Sr
    Joseph Gauthier Sr May 13, 2014

    Prior to taking everything out take a couple pics to make sure you get the door in the correct position when reassembled.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 91 Answers

Once you have the 5 screws out , you should be able to grab the motor and give it a twist for it to come out..

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d784e

Posted on May 13, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

defadad
  • 351 Answers

SOURCE: removing and replacing passenger side mirror 2002 town and country van

there should be a triangle shaped plastic section on the interior of the door behind the mirror, check it for a little plastic screw cover to remove it or you may just have to lever it gently to remove it.
once it is off it exposes the mirror retaining bolts which you undo to remove the mirror, I presume it has electric mirrors and if that is the case you will have to find the electrical wire plug for the mirror and pull it apart, replace mirror in reverse order of removing

Posted on May 13, 2009

  • 412 Answers

SOURCE: heater blower motor will not come on

it is located behind the glove box..2 wire connectors and 2 screws hold it into heater box..fairly inexpensive part

Posted on Jun 12, 2009

  • 1986 Answers

SOURCE: Replacing bulbs in tail lights in a Town and Country.

  1. Open your tailgate.
  2. Look for two (2) round flat black discs about the size of a dime (but thicker) on the inside of the body (between the red lens and the weather striping).
  3. Using a pair of pliers, pull out each of these two discs.
    • Note they are in tight and may require a fair bit of force to remove.
  4. Make sure the inner part of the disc also comes out. There are two parts to this system, a grommet and a plug:
    1. Push the plug backwards through the grommet.
      • The grommet fits into the actual hole in the body, and is spread by the plug, the pressure holding them in place.
    2. Carefully remove both grommet and plug.
      • The lens assembly will fall away from the vehicle when you pull out the second grommet so be careful.
  5. Note the wiring harness that connects to a plug inside. Beside that plug are two holders for the actual bulbs.
  6. Remove the holder by pressing the sides inwards and pulling. The light socket should come out.

Posted on Oct 21, 2009

jturcotte
  • 8734 Answers

SOURCE: how to replace rear blower

from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Posted on Nov 04, 2010

ZJLimited
  • 17970 Answers

SOURCE: Replacing blower motor 2001 Chrysler Voyager.

Check this procedure to removal & installing Blower Motor...

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      zjlimited_93.jpg

      Fig. Removing the trim panel to access the rear blower motor (click for zoom)

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    zjlimited_94.jpg

    Fig. The rear blower motor is held in place by four screws

To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Keep us updated.

Posted on Nov 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cant find relay or fuse for 2008 chrysler town and country front blower motor it's not marked on the fuse box


Don't worry about. Open the glove box and release it the fold down. Tabs on the side or top. The resistor is right there, replace it. don't buy a junk one, You'll be doing this every year.

Jun 28, 2016 | Chrysler Cars & Trucks

1 Answer

Air sounds like it is on when i start my van


blower relay stuck with the contacts closed sending constant current to the blower. replace blower motor relay.

Dec 13, 2013 | 2002 Chrysler Town & Country

1 Answer

My front blower on my 2002 Town and Country won't shut off. It blows full speed any time the van is running.


replace blower motor resistor located behind the glove box apro 2 x 3 in 2 screws and wire

Jan 19, 2011 | 2002 Chrysler Town & Country

1 Answer

2002 Chrysler Town and Country Rear Heat/Air only on High


most of the time the resistor is located downwind of the blower motor so it should be not to fao from the blower motor in the right rear of the van behind the quater trim panel which is the hvac unit is located

Jun 01, 2010 | 2002 Chrysler Town & Country

1 Answer

1996 town & country van front heater blower


you will need to start by checking fuse,then power to motor,then blower motor resistor

Jan 29, 2010 | 2005 Chrysler Town & Country

2 Answers

Front blower not working fuse &relay good


all speeds?? get to the blower and rap on it, hammer, wrench, foot. if it starts working, its worn out, replace it.

Sep 23, 2009 | 2004 Chrysler Town & Country

1 Answer

Front climate control blower only works on high speed.


Replace your blower motor resistor
Resistor located under dash on passenger side in screwed into blower housing. May be able to be repaired. Requires soldering a small piece of "unmelted solder" across where the old fusible link was. look carefully at resistor. Or else just replace. Buy new. Junkyard resistor likely to be as bad as yours.

Jun 13, 2009 | 2002 Chrysler Town & Country

1 Answer

Town and country mini van


does it turn off when the car turns off? if so, you probably need a new blower motor resistor. They run about $80 but shop around. Fixed my problem right away

Jun 04, 2009 | 2002 Chrysler Town & Country

1 Answer

2002 Chrysler Blower Motor - Van than postal truck hit


is the blower unit getting power at the plug in? use 12v light tester, if so then your ground good? if so you need a new blower simple!

Dec 29, 2008 | 2002 Chrysler Town & Country

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...