Question about 2001 Chevrolet Malibu

1 Answer

RACK AND PINON SLOPPY I DON

I HAVE A BOLT WITH OFF SET SPACERS I NEVER WORKED ON THIS PART OF A CAR BEFORE I NEED A ILLUSTRATION

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Chevrolet Master
  • 450 Answers

1. Google it 2. see instructions on A1 Cardone web site., 3 go to library and look at the Chilton book, 4 Buy the Chilton book. Chilton book better than haynes book.

Posted on May 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Labor cost for rack & pinon 2004 Pontiac Montana


The rack and pinion will cost you around 150 or so. Labor should be 4 hours. Then you may want to get an alignment.

Jan 08, 2013 | 2004 Pontiac Montana

1 Answer

Had new rack and pinon boots replaced on 2000 3.5 RL now power steering seems to pull a lot to left. Repairman said I need an alignment? Do you normally have to get an alignment when you get new rack and...


Yes it is very possible the tie rod adjustment was not completely returned to it's previous position (not perfected by eye) after removing to install new boots; note be sure to ask that inner tie rod seals are ok, otherwise the boot replacement is only a temporary shield for the leak.

Jul 19, 2012 | 2000 Acura 3.5RL

1 Answer

Steering on my 2004 Lincoln LS 6 is tight, it stays in place and is not quick to return after I make a turn. Put new power steering pump and rack and pinon. Still same problem.


Have to have alignment done after any
front end work

Most repair shops don't have that capability
That is why you don't go to them

Still same problem?

Then the whole rack & pump was a questionable
diagnosis & repair

Any thing else you can add

I have a 2004 V8 LS

Aug 02, 2011 | 2004 Lincoln LS

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

Im trying to install bassani mid length headers for more power...whats involved in doing that..


yoy have to takke the h pipe down, take out mt . mount bolts trans crossmember bolts, drop h. pipe when you jack up engine you will havw to take steering loose from rack and pinon. push trans all the way over should give you enough room to do what you need to do.

Jun 16, 2010 | 1999 Ford Mustang Cobra

1 Answer

How fix a rocket pinon oil leak


Rocket Pinion? thats a new one, no such thing ; ) .....I think you mean Rack and Pinion. (Steering Rack Assy) you just need to buy a remanufactured unit at any parts store, after replacement, you will need to have the front eng aligned. I would recommend a repair shop do this for you.

May 13, 2010 | 1998 Ford Taurus

1 Answer

How can i change the rack and pinon on a 2000 hyundai sonata


the K-frame has to be lowered in order to slide the steering rack out. this is after you have disconnected the hydraulic lines, the tie-rod ends, the exhaust (flex) pipe, the steering column shaft universal (at the bottom of the steering column), the stabilizer bar links, and the 4 17mm bolts holding the rack to the K-frame.

Oct 11, 2009 | 2000 Hyundai Sonata

1 Answer

Help


no your fram is fine just replace the bolt and the rack and pinon and the motor mounts, but make sure that when you put the subframe back together it linds up right and it is not bent or twisted. because if it is it will happen again and again. thaks

Sep 06, 2008 | 2000 Pontiac Grand Prix

Not finding what you are looking for?
2001 Chevrolet Malibu Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...