Question about 1999 Chevrolet Blazer

1 Answer

Steps to reset a car alarm

1999 Chevy Blazer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

If you have the original key.. Turn it on (don't try to start it) for ten minutes, turn it of for ten seconds. Try to start. If it doesn't start you have to do a relearn. Ten minutes on, ten seconds of, do this three times, then try to start it. You will have to have a charger on it. because if the battery gets to low, you'll have to do it all over agian.

Posted on May 12, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bryant329
  • 125 Answers

SOURCE: 1999 Chevy Blazer Starter

the starter is located on the passenger side lower motor. it has two bolts in it that hold it in place. it actually goes through a hole/slot in the transmission to the flex plate.

1st. disconnect the negative cable on the battery.
2nd. raise the vehicle safely and place a jack stand under the vehicle out of your way but near where you will be working(for safety).
3rd. remove the two bolts that hold the starter in place.
4th. remove the wires from the back of the starter.
5th. install in reverse order of above.

note: there may be little plates between the starter and the mounting points called shims. if there are then make sure you put them back.

Posted on Sep 24, 2008

  • 2039 Answers

SOURCE: Reset factory alarm 1999 Chevy Venture

passager side lock and unlock the door try it out pierre

Posted on Oct 04, 2008

  • 39 Answers

SOURCE: 1999 Chevy Blazer

143a

Posted on Jun 23, 2009

  • 617 Answers

SOURCE: 1999 chevy blazer distributor cap diagram

need 8th digit of vin and engine size, email address to send diagrams to you

Posted on Feb 07, 2010

  • 189 Answers

SOURCE: 1999 Chevy Blazer Engine will not crank over. All

try turning the key over to the start position. then take a long screwdriver and touch it across the terminals on the starter. this should start your vehicle. if the sarter doesnt turn when you do this,then you have the starter locked up,and yo will have to take it off and install some shims under the bolts.if the starter is trying to turn and the lywheel isnt urning...then you have a locked up engine.

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anti Theft Alarm


If you disable your alarm system because of embarrassment ( a poor excuse for too lazy to fix) imagine your inconvenience when someone steals the vehicle because you didn't hear it go . IT may be a simple thing such as resetting the CPU with a code reader or going to a good auto electrician or chevy service centre to have it fixed

Feb 08, 2014 | Chevrolet Blazer Cars & Trucks

1 Answer

Will a 1994 - 2001 auto transmission fit a 1999 chevy blazer


nope wont work big difference 94 OBD 1 type and 1999 OBD 2 type transmission.electronics differents.

Apr 08, 2013 | 1994 Chevrolet S-10 Blazer

1 Answer

Alarm won't shut off on 1999 Chevy blazer 4x4


Is it factory alarm or aftermarket??. Try using the key to lock and unlock the doors driver and passenger then turn the ingnition on with the key and leave it in the key on engine off position for a few minutes and start the vehicle

Oct 14, 2012 | Cars & Trucks

1 Answer

NEED STEP BY STEP INSTRUCTIONS TO REMOVE AND REPLACE TRANS. IN 1999 CHEVY S10 BLAZER


You're probably not going to want to hear this, but you have to actually unbolt the body from the frame and jack up the body to get at the bolts that hold the transmission to the engine. Not a job for an amateur.

Feb 19, 2010 | 1999 Chevrolet Blazer

1 Answer

I have a 1999 chevy blazer and its stuck in 4 wheel drive low


while on level ground, start truck, shift tranni to netural, step on brake, shift from 4 low to low hi either through lever or push button which ever one you have. problem solved.

Dec 28, 2009 | 1999 Chevrolet Blazer

2 Answers

Wiring diagram for 92 chevy blazer


My 1992 Chevy blazer s-10 starts and then the door locks automatically starts locking and unlocking...It wont stay running either...

Jun 11, 2009 | 1992 Chevrolet S-10 Blazer

1 Answer

Reset factory alarm 1999 Chevy Venture


passager side lock and unlock the door try it out pierre

Oct 04, 2008 | 1999 Chevrolet Venture

1 Answer

1997 chevy blazer


Although you probably have found the problem by now (~ month ago) -Some factory alarms can interrupt the ignition path if tripped and not reset within a certain time. It kind of sounds like yours is permanently interrupted.
It might be of use to someone else if you reply with any solution you found so others can benefit from your education on the problem.

Aug 27, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...