Question about 2010 Ford Focus 1.8

Open Question

What is the torque spec for the 4 bolts spindle on a focus 2010

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

polarcycle
  • 1392 Answers

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Posted on Aug 16, 2009

  • 122 Answers

SOURCE: need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Posted on Sep 18, 2009

emissionwiz
  • 75066 Answers

SOURCE: spindle nut torque spec on a 2004 F-150

u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Posted on Feb 04, 2010

kirkx
  • 2019 Answers

SOURCE: whats the torque specs on a 2001 ford focus 2.0

You need to buy the manual, because you also need to know the order in which to torque them.
http://www.car-stuff.com/mmparts/ford-focus/repair_manual.html
usually you start at the middle and circle outward.
But they can differ. Some cars you always need to put in new head bolts. Others are done in several stages. This is too critical to take chances on.
If you really can't afford $19 for a manual, go to the library and xerox the pages.

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the toque spec for a 2010 RX350 front suspension coil top 3 nut bolt and the bottom 2 bolt.


I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure.
Best Manuals

Oct 01, 2016 | 2010 Lexus RX 350

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Caliper bolts get loose


the main mounting bolts? not guides?
caliper mount to knuckle bolts?
what torque did you use? in foot/lbs.

  1. id bet they are not factory spec bolts
  2. or you used the wrong torque page.
  3. or your tool is no good. (harbor fright tools?)
use a beam torque tool, it will never fib to you, like cheap clickers do.
I promise.
specs
tighten the caliper pin bolts to 26 ft. lbs. (36 Nm). Bottom bolt
there are 4 bolts specs here.
above pin
banjo 17ft/lbs
top B bolts is 61.5 foot lbs. (this came loose at 61 ?)
C spec is 5ft/lbs on bleeder nipples.

now alternator tack.
the rotor is warped so bad it bead the calipers to death.
the wheel bearing, is so bad , same.

ever check those for run out, and end play?
bingo if true.
damage and collateral damage are limitless.
and rust too. (entropy of all kinds)

Apr 16, 2014 | 2010 Suzuki Grand Vitara

1 Answer

I need to know the torque-specs on the bolts for the CV shaft on a 1993 90 s. I need both the specs for the 6 bolts that hold the cv shaft to the transmission, as well as the 1 big outer-spindle...


Axle shaft bolt should be torqued to 147 Ft Lbs plus 1/4 turn.

The six CV joint bolts should be 59 Ft Lbs.

Ball joint nut should be 48 Ft Lbs

Hope this helps.

Sep 08, 2011 | 1993 Audi 90

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

Replacing a oil pan gasket on a 2000 ford focus se........is it a simple job or is it involved? What are the torque specs on the oil pan bolts?


its a simple job no exact torque is needed as the bolts you are tightening will only require a ten millimeter socket to do it equivalent to a 1/4 inch bolt just snug them and top it all of with a half turn beyond that.simple job really .

Oct 28, 2010 | 2000 Ford Focus

1 Answer

2001 ford focus se


DO not retighten the cylinder head bolts

Tighten the cylinder head bolts in three stages in the sequence indicated

10------4-------2--------6----------8

7-------5-------1--------3----------9


STAGES 1 ------------20 Nm 14.75 lb
STAGES 2--------------40 Nm 29.51 lb
STAGES 3--------------90 degrees.

Apr 18, 2010 | 2001 Ford Focus

1 Answer

Whats the torque specs on a 2001 ford focus 2.0


You need to buy the manual, because you also need to know the order in which to torque them.
http://www.car-stuff.com/mmparts/ford-focus/repair_manual.html
usually you start at the middle and circle outward.
But they can differ. Some cars you always need to put in new head bolts. Others are done in several stages. This is too critical to take chances on.
If you really can't afford $19 for a manual, go to the library and xerox the pages.

Feb 09, 2010 | 2001 Ford Focus

1 Answer

Need cylinder head gasket torque specs.


looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Sep 18, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2010 Ford Focus 1.8 Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...