Question about 2003 Ford Mustang

Open Question

Remove rear seat

2003 mustang convertible

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3741 Answers

SOURCE: how to remove rear seat back 1987 mustang

Tools Required:

  • 3/8 inch Drive Ratchet
  • 3/8 inch Drive 3” Extension
  • 3/8 inch Drive 10mm Socket
  • 3/8 inch Drive 13mm Socket
  • T-50 Torx Bit
  • 1/4 inch Allen Wrench
  • 3/16 inch Allen Wrench
  • 1/2 inch Wrench
  • Drill Motor
  • 1/8 inch Drill Bit
  • 5/16 inch Drill Bit
  • 2 inch Hole Saw
  • Trim Tool (Fork Tool)
  • Electrical Tape
  • Center Punch
  • Hammer
------------------- Installation:

Remove Back Seat:
  1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
  2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
  3. Remove Quarter Trim Panels:
    1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
    2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
    3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
    for more help click this link directly
    1. http://www.americanmuscle.com/05-07-lightbar-install.html ---------

Posted on Oct 05, 2009

  • 22 Answers

SOURCE: rear seat floor wells get about an inch of water

check drain tubes or hose under car may be cloged

Posted on Oct 09, 2009

emissionwiz
  • 75822 Answers

SOURCE: how do you remove 89 convertible mustang rear seat

hit it hard (with the side of your hand or palm) at the bottom of the seat on the right and the left to relase the spring retainers, run a putty kniofe under the seat edge to locate the spring retainers

Posted on Apr 03, 2010

Gozer
  • 435 Answers

SOURCE: 2001 mustang convertible. How

The seat bottom is held in with 2 release buttons located left and right of the center of the seat. (see photo) push with a screw driver and lift, then pull the seat bottom forward and remove.


gozer.jpg
The rear seat back is help in place by 2 self tapping bolts on the lower left and right of the seat back near the floor, if I remember correctly you'll need a 10mm socket. Remove the 2 bolt and lift up to remove the seat back. When re installing the seat back do not over tighten the bolts they have a tendency to strip.

Posted on Aug 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Mustang. Where is the cylinder that moves the top up and down located?


There are two, one on each side. You have to remove the rear seat and the trim panels on each side of the rear seat. The hydraulic cylinders are behind those.

Jul 24, 2015 | Ford Cars & Trucks

1 Answer

How to remove hydraulic lift cylinder from 2001 mustang conv V6


need to remove all plastic panels on the rear seat remove seat and remove the convertible top assembly complete

Sep 09, 2014 | 2001 Ford Mustang Convertible

1 Answer

How to remove rear seat on 2003 mustang convertible


There are two latches for a full size seat. One on each side of the car. Grab the seat and push back towards the truck and pull it up at the same time. they can be difficult. Some of the older models have bolts you have to remove. Run your fingers under the seat, they are located in the middle of where you sit.

May 12, 2014 | 2003 Ford Mustang

1 Answer

2001 mustang convertible. How do you remove the rear seat to access the motor or pump ot check oil level? Thanks, Bruce


The seat bottom is held in with 2 release buttons located left and right of the center of the seat. (see photo) push with a screw driver and lift, then pull the seat bottom forward and remove.


gozer.jpg
The rear seat back is help in place by 2 self tapping bolts on the lower left and right of the seat back near the floor, if I remember correctly you'll need a 10mm socket. Remove the 2 bolt and lift up to remove the seat back. When re installing the seat back do not over tighten the bolts they have a tendency to strip.

Aug 15, 2011 | 2001 Ford Mustang

1 Answer

I NEED TO REMOVE THE FRONT SEAT HEADRESTS FROM A 2004 FORD MUSTANG CONVERTIBLE.


Lift the headrest to it highest postion. Insert a thin stick parallel to the head rest bar (the side facing the rear of the vechicle) I used a thin paint stirring stick, a Slim Jim is ideal.
Once the stick is inserted (10" give or take) push the head rest down holding the stick steady, then pull the headrest back up and it will come off the seat.
Hope this helps.

Apr 03, 2010 | 2004 Ford Mustang

1 Answer

How do you remove 89 convertible mustang rear seat


hit it hard (with the side of your hand or palm) at the bottom of the seat on the right and the left to relase the spring retainers, run a putty kniofe under the seat edge to locate the spring retainers

Apr 02, 2010 | 1989 Ford Mustang

1 Answer

How to remove rear seat back 1987 mustang convertable?


Tools Required:
  • 3/8 inch Drive Ratchet
  • 3/8 inch Drive 3” Extension
  • 3/8 inch Drive 10mm Socket
  • 3/8 inch Drive 13mm Socket
  • T-50 Torx Bit
  • 1/4 inch Allen Wrench
  • 3/16 inch Allen Wrench
  • 1/2 inch Wrench
  • Drill Motor
  • 1/8 inch Drill Bit
  • 5/16 inch Drill Bit
  • 2 inch Hole Saw
  • Trim Tool (Fork Tool)
  • Electrical Tape
  • Center Punch
  • Hammer
------------------- Installation:

Remove Back Seat:
  1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
  2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
  3. Remove Quarter Trim Panels:
    1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
    2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
    3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
    for more help click this link directly
    1. http://www.americanmuscle.com/05-07-lightbar-install.html ---------

Oct 05, 2009 | 1987 Ford Mustang

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

Not finding what you are looking for?
2003 Ford Mustang Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...