Question about Cars & Trucks

1 Answer

Headlamp cover won't close - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 46 Answers

What year and model do you have? Some are controlled by vacuum and others by electric. Is it just one side or both? has it been slowly happening or was it all of a sudden?

Posted on Jun 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I FIND THE FUSE FOR THE RUNNING LIGHTS


Open the hood of your vehicle and disconnect the battery's negative-terminal cable with a socket wrench.
Remove the cover from the fuse block and locate the high-beam headlamp fuse. Most vehicles have two, one for the right headlamp and one for the left headlamp. For the exact location of the fuse, check through your vehicle's user's guide.
Use a fuse puller tool to remove the high-beam headlamp fuse and install a replacement fuse in its place. Reattach the cover to the fuse block.
Reach behind the high-beam headlamp and disconnect its electrical connector by pulling it straight out. Rotate the old bulb counterclockwise and pull it out to remove it.
Install a replacement bulb and reattach the electrical connector to the headlamp. Consult your vehicle's user's guide for the exact type of bulb to use. Close the hood when done.
V15 GDS VCI Diagnostic Tool for Hyundai and Kia

Sep 26, 2014 | Cars & Trucks

1 Answer

How do I replace the headlight assembly MN133516


The 2003 Outlander utilizes replaceable (9007) headlight bulbs. If you're looking to replace the bulb(s);
1. Raise the hood.
2. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. This will allow access to the headlight bulb.
3. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Do not touch the glass of the new bulb.
4. Place the socket back into the assembly, and twist it clockwise. Reattach the plastic cover, and close the hood.
Are you needing DIY instructions for replacing the entire headlamp assembly? Left (driver) or Right (passenger)?

Jan 18, 2013 | 2003 Mitsubishi Outlander

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

How to change headlight lamp in 2005 Pontiac g6


To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Dec 25, 2010 | Pontiac G6 Cars & Trucks

1 Answer

Head lamp replacement on a cadilic catera


  1. Open the hood.
  2. Unscrew the self-locking tab on the left side radiator cover.
  3. Unclip the left side radiator cover from the body to remove the left side radiator cover.
  4. Remove the battery.
  5. Remove the rubber protective cover from the back of the headlamp to reveal the bulb.

  1. Separate the bulb fastening tangs (1).
  2. Carefully remove the bulb.
  3. Remove the electrical connection from the bulb.

INSTALLATION PROCEDURE:

  1. Install the electrical connection to the bulb.
  2. Snap the fastening tang (1) in place to install the bulb.
  3. Install the rubber protective cover to the back of the headlamp.
  4. Install the battery.
  5. Seat the tab to the body of the left side radiator cover.
  6. Secure the left side radiator cover by turning the self-locking tab.
  7. Close the hood.
  8. Reprogram the applicable accessories. this is for a 1998 what year is yours if its newer its a different procedure tell me if it is

Dec 24, 2010 | Cadillac Catera Cars & Trucks

1 Answer

I need to change the headlights


REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

  1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
  2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
  3. Pull the headlamp assembly out and away from the vehicle
  4. Disconnect the headlamp electrical connector.
  5. Remove the headlamp assembly from the vehicle.
  6. Remove the headlamp bulb cover from the headlamp assembly.
  7. Remove the headlamp bulb socket from the headlamp assembly.
CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Remove the headlamp bulb.
  2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
  3. Remove the side marker bulb.
  4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
  5. Remove the parking lamp bulb.
INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Install the headlamp bulb to the socket.
  2. Install the headlamp bulb socket to the headlamp assembly.
  3. Install the headlamp bulb cover to the headlamp assembly.
  4. Install the side marker bulb to the socket.
  5. Install the side marker bulb socket to the headlamp assembly.
  6. Install the parking lamp bulb to the socket.
  7. Install the parking lamp socket to the headlamp assembly.
  8. Connect the headlamp electrical connector.
  9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
  10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.
NOTE: Refer to Fastener Notice in Service Precautions.
  1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
Tighten the bolts to 6 N.m (53 lb in).


  1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
  2. Close the hood.
3e4ca4a.gif

Oct 21, 2010 | 2006 Cadillac SRX

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How do i change both headlights on my 2002 chevy cavillier


    Removal & Installation To Remove:
    1. Remove or disconnect the following:
      • Hood close out filler panel.
      • Bolts from the headlamp.
      • Headlamp from the headlamp mounting panel.
      • Electrical connector from the headlamp.
      • Headlamp bulb/socket retainer ring from the headlamp.
    c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    How is cornering lamp changed in 2002 Buick Regal.



     
     
    Lighting
    Headlight Assembly
    Removal & Installation
    To Remove:

    Open the hood.
    Apply light pressure to the headlamp lens to hold the headlamp in place while disconnecting the retainers.
    Lift up the retainers to release and remove the retainers.
    Remove the headlamp mounting tabs from the slots in the upper fascia support and fender reinforcement.
    Disconnect the wiring harness from the headlamp assembly.
    Remove headlamp.
    Remove the rubber access cover from the appropriate bulb to be replaced.
    Rotate the headlamp bulb/socket counterclockwise to remove from the headlamp assembly.
    To Install:
    Connect the wiring harness to the headlamp.
    Install the headlamp bulb/socket to the headlamp assembly rotating the socket clockwise until fully seated.
    Install the rubber access cover.
    Position the headlamp mounting tabs to the slots in the upper fascia and fender reinforcement.
    Apply light pressure to the headlamp lens to hold the headlamp in place while installing the retainers.
    Align the headlamp assembly retainers and slide them over the headlamp mounting tabs.
    Close the hood.

     
    Top of Form 1
    Bottom of Form 1

    Mar 30, 2009 | 2002 Buick Regal

    1 Answer

    Replace low beam headlamp, passenger side, 2004 Navigator


    Remove the front radiator air deflector.
    Remove the three bolts and the headlamp assembly.
      • Disconnect the electrical connectors.
    ef5d2b9.jpg
    Remove the headlamp bulb protective cover.
    1 Low beam cover. 2 High beam cover.

    babb381.jpg
    b8093f8.jpg

    Feb 13, 2009 | 2003 Lincoln Navigator

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    11 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...