Question about 2002 Jaguar S-Type
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: jammed seat belt
bet the belt is twisted pull back the rubber door seal and remove the top buckle should be possible to remove the trim pull the belt all the way out and untwist go for it
Posted on Jan 06, 2009
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
Dip beam (outer) headlight
Open the bonnet.
Slide open the two spring clips (A) and remove the cover (B).
Press the spring clip inwards and push towards the bulb
to release the bulb and then remove the bulb from the light
unit. Pull the connector from the bulb.
Fit a new bulb to the connector, type H1 for dipped beam.
Fit the bulb to the light unit, the bulb will only correctly fit in
one position. Engage the spring clips to retain the bulb and then
fit the cover and retain using the two spring clips.
Close the bonnet.
Note: High Intensity Discharge (HID) Xenon light units,
type D2S 35W, are not renewable, contact your Dealer if the headligh fails to operate
Posted on Oct 07, 2009
I had the same issue today with a 2004 jag.
1. Once I had the locksmith open the door. We proceeded to remove the back seat. Not an easy task, but this is the only way.
A. remove the plastic kick plate on floor leading to back seat. This will allow you to pull out the padded liner that is not part of the seat but cushions each side. It will not completely come out, but expose a star nut that must be turned loose with six more later on.
b. The front of the back seat is held down by two copper u shaped wires, that must be popped up and out of a white piece of plastic, Once this is done you can lift up the seat portion and remove it from the car. You will now see six star bolts that must be removed. After you take them out the round bar holding the upper portion of the seat can be removed or popped out enough so that you can seperate or spread the back portion of the seat from each other in sections. Once this is done you will be able to pull out a section far enough out to gain access to the trunk.
It takes about 15 minutes once you understand what your doing, and about an hour if you have never done it. The trick is allowing the lock smith to open the car. The alarm will sound off for about 2 minutes then stop. Unless you have the rear center console removalbe panel and arm rest, then the only course is exactly what I did, removing the back seat. They charged me 150.00 dollars with me doing most of the work. Not much I could say, as I was the *** that locked my keys in the trunk. Best bet for a Jag is to carry another key with electronic trunk opener mounted underneath the car in a key lock box. Well worth the investment, as most people end up getting their car towed.
It is poor feature on a Jag that the only way you can get in a locked trunk is through the back seat, but this is how it is done.
Believe me, it is the only way other than having it towed to the Jag dealer so he can figure out. Thier is a way to jump a wire under the passenger side dash, but you may end up shorting out the whole electrical system, I dont think it is worth the risk, unless the person doing it, has previous experince. Hope this helps, and happy tearing out your back seat. You can do it, the first time is always a little tough.
Posted on Oct 19, 2009
SOURCE: Jaguar x type 2004 front bumper
Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.
Becareful not to damage the fog lamp harness upon removal
Posted on Apr 24, 2010
Tips for a great answer:
Oct 21, 2016 | 2002 Jaguar S-Type
Oct 05, 2011 | 2002 Jaguar S-Type
Mar 17, 2011 | 2005 Jaguar X-Type
Dec 10, 2010 | 2002 Jaguar X-Type
Sep 02, 2010 | 2002 Jaguar X-Type
Aug 25, 2010 | 2002 Jaguar S-Type
Feb 20, 2010 | 2002 Jaguar S-Type
Aug 11, 2009 | 2002 Jaguar S-Type
Jan 01, 2009 | 2003 Jaguar X-Type
Dec 01, 2008 | 2002 Jaguar S-Type
16 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: