Question about 1998 Ford Ranger SuperCab

1 Answer

Windshield wipers stay on? - 1998 Ford Ranger SuperCab

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 1,832 Answers

-Possibly relay stuck (ON Position)
-Unplug the relay and if it stop then the relay need to replace.

Good luck

Mai

Posted on May 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

1996 crown vic- drivers side wiper arm loose, blade will not lay flat when cleaning


Sometimes you need to bend the arm to put more pressure on the glass.

Mar 29, 2014 | 1996 Ford Crown Victoria

1 Answer

Car does not turn off after changing fuse


car stays, on, does that mean engine will not shut down.
or mean the wipers stay on, after turning them off
1:yes, wiper, bad internal wiper switch, (bad wiper motor)
2: no:?
wiring hacks (after market installs of something gone worn)
bad igniton switch.

Dec 12, 2013 | Acura Integra Cars & Trucks

1 Answer

Windshield wipers stay up when i turn them off


To Question on Windshield wipers stay on. Your parking paw is defective. Its best to replace the windshield motor, There usally easy to replace

Oct 27, 2011 | 1997 Chevrolet Venture

1 Answer

What is the good windshield wiper ?


The REFLEX styles that stay pressed firmly to the windshield ( hinge free style) Rain-X and Armor all both make this style. bout 40 bucks for a pair.

Apr 22, 2010 | 2002 Toyota Sienna

1 Answer

Windshield wiper problems


The motor park switch is bad.

Dec 10, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

Windshield wipers stay up on the windshield, wont go back down when i shut them off


There is a wiper pulse board on the wiper motor itself that is failing, this can be replaced without replacing the entire unit.

Jun 28, 2009 | 2001 Chevrolet Venture

1 Answer

1999 Chevy Venture, Windshield wipers stop in upright position


You will need to replace the wiper transmission.This is a common problem.

Jan 24, 2009 | 1999 Chevrolet Venture

2 Answers

Windshield wiper problem


check the wiper arms first take off the end caps loosen bolts and adjust then tighten then try again please rate my response thank you very much

Jul 17, 2008 | 1998 Pontiac Firebird

Not finding what you are looking for?
1998 Ford Ranger SuperCab Logo

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...