Question about BMW 316i

Open Question

Bmw 316i dimmer switch not working

Dimmer switch not working

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bmw_tech_38
  • 113 Answers

SOURCE: Radiator removal BMW 316i

hi, the two clamps that secure the radiator have a small slot on the top, if you insert a small screwdriver into the slot and use it as a pry bar you should be able to unclip the holding clamp and it then releases like a hinge.

Posted on Feb 24, 2009

Ad
  • 219 Answers

SOURCE: bmw 316i

hi markjones, the ignition switch can usually be removed without too much disassembly. First you will need to remove a plastic screw in the upper and lower trim covers. Seperate the covers. You should see a black plastic ring around the mechanical switch. gentley remove the ring. Next remove the rubber o-ring/band. With the key in the iginition and turned to almost to position 1, insert a heavy duty paper clip, or bmw special tool (about $30 from the dealer) into the small hole in the switch. There is a cam in the hole that needs to be twisted clockwise so the cylinder can be removed. When installing a new switch make sure to remove the little tab pice of metal that usually breaks off in the housing. Also be sure to make sure and reinstall the rubber ring/band because they are part of the ews system. If you key turns continuously, or is not able to be removed, the ignition housing and cylinder both will need replaced. Replacing the lock housing is about a 2 hour sequence and can be challenging. I would recommend a shop for that kind of repair.

Posted on Apr 22, 2009

ILikeBMW
  • 117 Answers

SOURCE: 1999 bmw 316i location of sensors

hello there

the coolant level sensor is at the bottom of the raidiator, ther is an electrical wire going to it so you sould find it easily.

Hope this helps, please don't forget to rate me.

Posted on May 19, 2009

stanley141
  • 124 Answers

SOURCE: bmw 316i overheating

check if the water is circulating as you might have a blockage in the header tank. this can be checked by opening the radiator cap and check if the water is circulating on top.

Posted on Jul 28, 2009

  • 534 Answers

SOURCE: BMW 316i E36 1994, Rear window demister isn't

Check rear demister control relay operation,
Check for presence of 12V power (and ground connection) at rear window heater connection.

Check continuity of the rear window heating element.

Posted on Aug 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

What are the instructions to reset the radio in a BMW 316i 1995.


If you do not have an instruction book, ask google.

Mar 16, 2015 | BMW 316i Cars & Trucks

1 Answer

How do I replace a oil pump on bmw 316i m43 1995 model


Slide under your BMW wearing very little. Yell loudly and ask somebody how do you change your oil. See what happens and
keep an open mind about it.

Jan 18, 2015 | 1994 BMW 316i

1 Answer

Bmw 316i 1998 ignition wont turn


Not familiar with the 316i but have had 97 M3 which exhibited similar trait. If the car is manual transmission try to gently pull the steering wheel to each direction while trying the key. If the vehicle is an automatic make sure the shift lever is all the way into the park position. In both cases it could be the safety interlock is causing the problem.
Depending on the mileage of the car - and for a 98 at an average yearly rate of 12K per year - I'm guessing the miles are up there, the ignition switch iteself could need replacing. If you have a good shop manual (Bentley) and posses mechanical abilities it is not too difficult.

Sep 03, 2014 | 1998 BMW 316i

1 Answer

Drivers window on e30 bmw 316i touring goes down but not up.can i put the window up manually?


Not without disassembling the door. If you are handy you can take apart the window switch and clean it. If not try spraying compressed air into the switch. The switch is likely dirty.

Mar 18, 2010 | 1996 BMW 318

1 Answer

Locate ignition module 1990 BMW 316i E


The ignition is controlled by the motronic control unit its mounted on the passenger side of the dash above the glove compartment.

Jan 30, 2010 | 1990 BMW 3 Series

1 Answer

Where would i find the starter motor on bmw 316i 1994 -1998 please


For BMW 316i 1994 - 1998 you will find the starter motor on the right part of the car at the bottom back right side of the engine, between clutch case (or automatic gearbox case) and cylinder block.

Jan 28, 2010 | 1994 BMW 3 Series

1 Answer

BMW 316i E36 1994, Rear window demister isn't working, Fuses are ok, demister switch lights up when pressed. Any suggestions on how to trouble shoot?


Check rear demister control relay operation,
Check for presence of 12V power (and ground connection) at rear window heater connection.

Check continuity of the rear window heating element.

Aug 17, 2009 | BMW 318 Cars & Trucks

1 Answer

How do i change the torque settings on my bmw e36 316i 1991 j reg its not a 318i but parts of a 318i would thay fit a 316i and work fine


Hi unsure what you mean by change the torque settings, if you mean on the head question is why? If yes for head, there is a tool for that & go to Download PDF search | PDFTown.com
for more info

Jul 08, 2009 | 1996 BMW 318

2 Answers

Radiator removal BMW 316i


hi, the two clamps that secure the radiator have a small slot on the top, if you insert a small screwdriver into the slot and use it as a pry bar you should be able to unclip the holding clamp and it then releases like a hinge.

Feb 20, 2009 | 1996 BMW 318

1 Answer

316i bmw


I WOULD LIKE YOU TO CHANGE YOUR PCV VALE FITTED TO YOUR INLET MANIFOLD

Jan 21, 2009 | 2003 BMW 5 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...