Question about 2000 BMW 323i

Open Question

How do I check transmission fluid on BMW 323i 2000 model

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2000 BMW 323i windshield washer fluid won't work

Had the same problem with my 2001 330ci. If not used frequently the pump will get waterlogged and allow fluid to seep into the motor. I was able to disassemble, clean, and rebuild my pump but I would recommend replacing it, it is not expensive at around $20-30 and easy to change.

The washer pump is inserted into a hole on the washer tank itself. It is an interference fit so it will pop out. If you have significant amount of fluid in the tank it will leak out of the hole. There should be one hose connected with a clamp and one electrical connector. I believe there may be a plastic shroud covering it which needs to be unsnapped.

Good luck!

Posted on Jun 25, 2009

Ad
alicantecoli
  • 22156 Answers

SOURCE: 2000 bmw 323i service engine soon light code =

you can buy a cheap scanner that will put this light out,i have a mechanic working for me that stands on the roof ,tweeks the radio and has one foot on the brake whilst turning on the lights and he puts out nearly every service light you can think of but he wont show anyone least of all me,but if it its a 99 model iam sure you can put the light out by using a 12v electrical screwdriver with the light inside and a cable comes out the end with a clip .then going across the pins on the special BMW connector block it will go out with the resistance of the bulb across it ,but ??big but ?does it have an OBDII connector or the round BMW type because we dont have OBDII on pre 2005 cars here in spain .Now we do and guess what ??its all encrypted software used ...makes me a dinasaur

Posted on Aug 14, 2009

  • 31 Answers

SOURCE: flashing headlights in a 2000 bmw 323i

lose wire or lose ground wire

Posted on Aug 29, 2009

Molson02536
  • 3854 Answers

SOURCE: how often do i need oil change on a 2000 323i bmw?

2000 BMW 323Ci 2.5L 6-cyl Engine Code M52 B25
Engine Oil
Grade 1......SEO
All TEMPS......5W-30
CAPACITIES: Engine, with filter..........6.5 liters

2000 BMW 328Ci 2.8L 6-cyl Engine Code M52 B28
Engine Oil
Grade 1......SEO
All TEMPS......5W-30
CAPACITIES: Engine, with filter..........6.5 liters

Service every 3,000 city 5,000 hyway miles.

Posted on Dec 24, 2009

  • 14 Answers

SOURCE: I have the check engine code 1624 on my 2000 BMW

P1624- Pedal Position Sensor Potentiometer Supply Channel 1 Electrical.
The Siemens MSE43.0 Engine mamagement module is used on more than one model. The different meanings of the P1624 are based on your model.

The P1624 referenced here is for the MS43.0 engine management module with a note for M52 engines (323 / 328) that it is a coolant temperature below thermostat regulating temperature. You should have a M52 engine.

The MS42.0 engine mangement does not list a P1624 code in the Bentley manual.

The fault above cold be set due to the following:· Break/open in the wiring from the DME to the throttle motor(MDK).· The actuator or potentiometers inside the MDK could be contaminated.SOLUTION:
(If any of the faults listed are set) · Using a breakout box check for an open or short to ground in the wiring from the DME to the MDK.· If the wiring is intact then replace the MDK, then the adaptation values in the DME must be
cleared. Failure to do this will result in reoccurring faults.· Switch the ignition off for 30 seconds.· Turn on the ignition and delete the DME adaptations and the fault code
memory · Press the accelerator pedal to wide open throttle(WOT)4 times
MDK- motor driven throttle valve.

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 bmw 323i automatic transmission it starts but doesnt drive or reverse,what is the problem?


run the fault codes and look for a sensor / servo fault for the torque converter clutch

May 10, 2012 | 1999 BMW 323i

2 Answers

Should a 1999 323i BMW transmission fluid be changed when it's mileage is 197,000?????


BMW says that the transmission fluid is permanent. However, you have to keep in mind that they do not greatly care whether a car lasts 200k miles or 300k miles, so long as it makes it though the warranty period.
BMW also said that the previous generation (e36) fluid was permanent, and that has proven to be untrue.
I believe that the 1999 323 uses the later, really expensive, synthetic transmission fluid, so brace yourself for a hefty bill.
I recommend replacing the older generation fluid every 50k miles and the newer generation (yours) fluid every 100k miles. My wife's 330 is approaching 100k miles and I intend to replace her fluid soon.

Mar 04, 2011 | 1999 BMW 328 Series

1 Answer

WHAT TYPE OF TRANSMISSION FLUID IS NEEDED FOR 2000 BMW Z3 6 CYLINDER


On the manual the fluid is "lifetime" BMW MTF LT-1, SOME models used ATF. There is a plate on the side of the transmission that will give what your particular model was filled with.

On the automatic the fluid type should be printed on the "type plate" on the side of the transmission

both are usually Dexronn III ATF, but please check your plate!!!

Mar 13, 2010 | 2000 BMW Z3

1 Answer

I have a 2000 BMW 323I automatic transmission that will not go into reverse. All the forward gears seem to be working fine. I bought the car from a dealer who says the car was working fine before I bought...


hi changing fluid and filters sometimes cures problemiif not its probably reverse gear solenoid in gearbox .get a decent secondhand box if fluid change doesnt help.

Dec 06, 2009 | 1999 BMW 323 Series

3 Answers

2000 bmw 323i auto trans wont go in reverse. i just had the front and rear brake pads and rotors changed. the ABS light is on as well even after the change.


ive heard people say that on a auto transmission on a BMW that if it wont go into reverse there might be something wrong with the transmission... just a thought, i might be wrong

Jul 09, 2009 | 1999 BMW 323 Series

1 Answer

I have a 1999 bmw 323i. i need to know where the oil filter is and where to put the transmission fluid.


the oil filter is right in the middle of the engine (between the intake and valve cover gasket) near the radiator it has a 36mm cap over the top of it. the transmission doesn't have a dipstick. the fluid must be checked through a fill plug (transmission must be cool and vehicle running) would not attempt in driveway with vehicle on jackstands

Apr 18, 2009 | BMW 323 Cars & Trucks

Not finding what you are looking for?
2000 BMW 323i Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...