Question about 1990 Nissan Hardbody King Cab

1 Answer

Timing belt isnt moving when i turn the main crankshaft

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 40,701 Answers

This indicates a broken timing belt and will require the front of the motor to be pulled of to replace it . I suspect that you will have bent valves as well so the head will have to come off for then to be replaced . To do the job properly to obtain maximum life from the new belt ,Cam shaft seals ,crankshaft seal, hydraulic adjuster( if applicable), all idler pulley bearings must be replaced . The seals because oil destroys rubber belts well before due time and the pulley bearings will be worn out and will not see another full time period.

Posted on May 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace timing belt on 2002 kia spectre


Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE
    Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-0.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-3.gif
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

Feb 10, 2016 | 2002 Kia Spectra

1 Answer

How to install the timing chain


2.2L & 2.3L Engines
Except S2000 with 2.2L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the cylinder head (valve) and upper timing belt covers.
  3. Turn the engine to align the timing marks and set cylinder No. 1 to Top Dead Center (TDC). The white mark on the crankshaft sprocket should align with the pointer on the timing belt cover. The words UP embossed on the camshaft sprocket should be aligned in the upward position. The marks on the edge of the sprocket should be aligned with the cylinder head or the back cover upper edge. Once in this position, the engine must NOT be turned or disturbed.
  4. Remove all necessary components for access to the lower timing belt cover, then remove the cover.
  5. There are two belts in this system; the one running to the camshaft sprocket is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer shaft belt or timing balancer belt. Lock the timing belt adjuster in position, by installing one of the lower timing belt cover bolts to the adjuster arm.
  6. Loosen the timing belt and balancer shafts tensioner adjuster nut, do not loosen the nut more than one turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
  7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  8. Remove the balancer belt sprocket from the crankshaft.
  9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
  10. Remove the timing belt by sliding it off the sprockets. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  11. If defective, remove the belt tensioners by performing the following:
    1. Remove the springs from the balancer belt and the timing belt tensioners.
    2. Remove the adjusting nut from the belt tensioners.
    3. Remove the bolt from the balancer belt adjuster lever, and then remove the lever and the tensioner pulley.
    4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
  12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time.
  13. To install:
    1. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and tighten the mounting bolts to 106 inch lbs. (12 Nm).
    2. If the tensioners were removed, perform the following procedures:
      1. Install the timing belt tensioner lever and the tensioner pulley.
      2. Install the balancer belt pulley and adjuster lever.
      3. Install the adjusting nut and the bolt to the balancer belt adjuster lever.
      4. Install the springs to the tensioners.
      5. Install the lockbolt to the timing belt tensioner, then move it its full deflection and tighten the lockbolt.
      6. Move the balancer it's full deflection and tighten the adjusting nut to hold its position.
    3. The pointer on the crankshaft sprocket should be aligned with the pointer on the oil pump; the camshaft sprocket must be aligned so that the wordUP is at the top of the sprocket and the marks on the edge of the sprocket are aligned with the surfaces of the head or the back cover upper edge.
    4. Install the timing belt on the sprockets in the following sequence: crankshaft sprocket, tensioner sprocket, water pump sprocket and camshaft sprocket.
    5. Check the timing marks to be sure that they did not move.
    6. Loosen, then retighten the timing belt adjusting nut; this will apply the proper amount of tension to the timing belt.
    7. Install the timing balancer belt drive sprocket and the lower timing belt cover.
    8. Install the crankshaft pulley and bolt, tighten the bolt to 181 ft. lbs. (245 Nm). Rotate the crankshaft sprocket 5-6 turns to position the timing belt on the sprockets.
    9. Set the No. 1 cylinder to TDC and loosen the timing belt adjusting nut one turn. Turn the crankshaft counterclockwise until the cam sprocket has moved 3 teeth; this creates tension on the timing belt.
    10. Tighten the timing belt adjusting nut.
    11. Set the crankshaft sprocket and the camshaft sprocket to TDC. If the sprockets do not align, remove the belt to realign the marks, then install the belt.
    12. Remove the crankshaft pulley and the lower cover.
    13. With the timing marks aligned, lock the timing belt adjuster in place with one of the lower cover mounting bolts.
    14. Loosen the adjusting nut and ensure the timing balancer belt adjuster moves freely.
    15. Align the rear timing balancer sprocket using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt/rod into the hole and align the 2.9 in. (74mm) mark with the face of the hole. This will hold the shaft in place during installation.
    16. Align the groove on the front balancer shaft sprocket with the pointer on the oil pump.
    17. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the bolt from the maintenance hole and reinstall the bolt and washer.
    18. Install the crankshaft pulley, then turn the crankshaft sprocket 1 turn counterclockwise and tighten the timing belt adjusting nut to 33 ft. lbs. (45 Nm).
    19. Remove the crankshaft pulley and the bolt locking the timing belt adjuster in place.
    20. Install the lower and upper timing belt covers, and all applicable components. When installing the crankshaft pulley, coat the threads and seating face of the pulley bolt with engine oil, then install and tighten the bolt to 181 ft. lbs. (250 Nm).
    21. Install the cylinder head cover gasket cover to the groove of the cylinder head cover. Before installing the gasket thoroughly clean the seal and the groove. Seat the recesses for the camshaft first, then work it into the groove around the outside edges. Be sure the gasket is seated securely in the corners of the recesses.
    22. Apply liquid gasket to the four corners of the recesses of the cylinder head cover gasket. Do not install the parts if 5 minutes or more have elapsed since applying liquid gasket. After assembly, wait at least 20 minutes before filling the engine with oil.
    23. Install the cylinder head (valve) cover and all other applicable components.
b0b9eb99-5646-47c3-bfea-3ed501154864.jpg dc472561-14cf-4143-9a20-b37ba89f57de.jpg

Jul 02, 2014 | 2004 Honda Accord

1 Answer

How to position the timing belt crank shafts of 1997 mazda mpv


Raise and support the vehicle on jack stands. Remove the wheel on the passenger side of the vehicle using the drive ratchet and a socket. Remove the passenger side splash shield, using the drive ratchet and a 10mm socket. 2 Remove the accessory belt(s), using a wrench to loosen the tension. Unscrew the bolt from the crankshaft pulley, using the drive ratchet and a socket. Slide the crankshaft pulley and the timing belt guide washer directly behind it off the crankshaft.3 Remove all the 10mm bolts in the top and bottom timing belt covers. Remove the covers. The drive ratchet and a 10mm socket works well for this. 4 Push the crankshaft pulley on the crankshaft just enough to engage the keyway. Turn the crankshaft pulley clockwise until the timing mark on the top camshaft sprocket, which is marked with a line on the sprocket with a number 1 next to it, is lined up with the pointer straight up on top of the cover to the rear of the sprocket. Once the top mark is lined up, the crankshaft pulley's semi-circle mark should be lined up with the triangular pointer on the block. The marks on the crankshaft pulley should be straight up and the keyway should also be straight up. Remove the crankshaft pulley. 5 Loosen the tensioner bolt with a wrench, pull the tensioner to the left, away from the belt and loosely tighten the bolt to hold it in place. Remove the timing belt. 6 Install the timing belt counter-clockwise starting at the crankshaft pulley and move upward over the outside the water pump, on the inside the guide pulley and over the top of the camshaft, ending on the inside the tensioner. The main thing when installing a timing belt is to ensure the belt is as tight as possible opposite the tensioner. Get the belt tight between the crank sprocket and the cam sprocket so the tensioner can take out all the slack without moving the timing marks.7 Loosen the tensioner bolt and allow the tensioner to apply pressure to the belt. Use your hand to apply a slight pressure to the tensioner toward the belt and tighten the tensioner bolt. Check the belt tension to ensure it is not too tight or too loose. Check the timing marks again to ensure they still align. If the timing marks are not lined up, loosen the tensioner, move it back and repeat the last procedure over again until the belt is tensioned properly with no misalignment of the timing marks. 8 Install the crankshaft pulley temporarily and turn the pulley two complete revolutions, once again aligning the mark on the crankshaft pulley. Ensure the timing mark is still lined up perfectly on the camshaft sprocket. Reinstall the remaining parts in reverse order of removal

Oct 14, 2011 | 1997 Mazda MPV

2 Answers

2004 kia rio timing belt replacement procedure


from autozone.com

Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.

25f366d.jpg

b46eac9.jpg

503792b.jpg
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

1.6L (VIN 3) & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Engine cover Right-hand front wheel Right-hand wheel well side cover Accessory drive belts Water pump pulley Timing belt upper cover
  3. Turn the crankshaft pulley so cylinder No. 1 is at Top Dead Center (TDC). Align the pulley groove with the timing mark T of the timing belt cover.
  4. Remove or disconnect the following:
    NOTE If the timing belt is to be reused, mark the belt to indicate its turning direction.


    Crankshaft pulley Crankshaft flange Lower timing belt cover Timing belt tensioner Timing belt

To install:
  1. Align the timing marks of the camshaft and crankshaft sprockets to ensure the No. 1 cylinder is at TDC.
  2. Temporarily install the timing belt tensioner.
  3. Install the timing belt over the crankshaft sprocket, then inside the idler pulley, over the camshaft sprocket and then inside the timing belt tensioner.
  4. Apply tension to the timing belt by turning the tensioner in the clockwise direction so there is no slack in the belt on the tension side.
  5. Tighten the tensioner mounting bolts to 20 ft. lbs. (27 Nm).
  6. Check the timing belt tension as follows:
    1. 1.6L (VIN 3) engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end is approximately 1 / 2 of the tensioner mounting bolt head radius away from the bolt head center.
    2. 2.0L engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end sags approximately 0.16-0.24 inches (4-6 mm).

  7. Turn the crankshaft two turns in the clockwise direction and realign the crankshaft sprocket and camshaft sprocket timing marks.
  8. Install or connect the following:

    Lower timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Crankshaft flange Crankshaft pulley. Tighten bolt to 101-109 ft. lbs. (138-147 Nm) for 1.6L (VIN 3) engine and 123-130 ft. lbs. (168-177 Nm) for 2.0L engine. Upper timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Water pump pulley Accessory drive belts Right-hand wheel well side cover Right-hand front wheel Engine cover Negative battery cable

Sep 06, 2010 | 2004 Kia Rio

1 Answer

1987 Dodge Ram 50 2.0 L engine. My main timing belt was stripped. I replaced it and the secondary belt at the same time. When turning the crankshaft clockwise, the distributor rotor does not move. I...


Yes, the crank will spin a few times to each rotation of the rotor. If you have the timing belt on, you should be able to crank the engine with the starter. Just make sure you take the spark wire off the coil first so it wont start. Also make sure you lined up the marks on the crank and cam sprockets or you may have serious timing issues.
The engine is fairly hard to turn over with normal length socket wrenches. I use a breaker bar.

Aug 25, 2010 | 1987 Dodge Ram 50

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Remove water pump


Disconnect battery earth lead. Do not turn crankshaft or camshaft whn timing beld removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated) Do not turn engine via camshaft or other sprockets. Observe all tightening torques. Remove engine, remve RH engine mounting. Remove auxiliary drive belts, water pump pulley, crankshaft pulley, timing belt upper cover, timing belt lower cover. Turn crankshaft clockwise to TDC on No. 1 cylinder, slacken tensioner bolts 5 & 6. Move tensioner away from belt and lightly tighten bolts. Remove timing belt. Remove water pump and replace with new one. Suggest to replace cambelt as well.
Installation
Ensure timing marks aligned3 & 4. Fit timing belt in anti-clockwise direction, standing at crankshaft sprocket. Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner bolt 5. slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner bolt 6. Tighten tensioner bolt 5. Turn crankshaft on turn clockwise. Ensure crankshaft sprocket timing marks aligned 4.
Slacken tensioner bolt 5. Slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner 6. Tighten torque: 20 - 26 Nm. Tighten tensioner bolt 5. tighten torque: 20 - 26 Nm. Apply thumb pressure to belt at middle. Approximately 5kg. Belt should deflect to 1/4 of tensioner bolt head width 7. Belt tention can also be set using burroghs (BT-33-73F) tension gauge 10 at middle. Turn crankshaft 90 ° anti clockwise. Check belt tension is 9.5 16,5kg (engine must be cold). Install components in reverse order of removal. Fit cranckshaft pully. Tighten crankshaft pully bolts 8. G4-J: Tightening torque: 12-15Nm.
G4-N/G4-k: Tightening torque: 10-12Nm
G4EA: Tighten crankshaft pully bolt 9. Tighten torque: 140-150Nm.

Nov 04, 2009 | Hyundai Excel Cars & Trucks

1 Answer

How i fix timing of lantra 1600 cc 95


Disconnect battery earth lead. Do not turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of ratation unless otherwise stated, Support engine. Remove, engine mounting, auxilliaty drive belts. Water pump pulley 1. Crankshaft pulley bolts 21. crankshaft pully 2. timing belt covers 3. Turn crankshaft to TDC on No 1 cyclinder. Ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket and balancer shaft sprocket timing marks aligned. Timing marks on camshaft sprockets should align with cylinder head upper face. Dowel pins on camshaft sprockets should face upwards. Slacken tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove, automatic tensioner unit bolts. Automatic tensioner unit. Timing belt, crankshaft centre bolt, crankshaft sprocket. Crankshaft sprocket guide washer. Slacken blancer shaft belt tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove balancer shaft belt.

Installation
Ensuring timing marks arligned. Note timing marks on camshaft sprockets should align with cylinder head upper face. Exhaust sprocket mark is on recess, but inlet sprocket mark is on tooth. Note: to check oil pump sprocket positioned correctly, removing blanking plug from cylinder block. Insert 8mm diameter Phillips srcrewdriver in hole. Ensure screwdriver is inserted 60mm from face of cylinder block. if screwdriver can only be inserted 20mm: turn oil pump sprocket 360°. Insert screwdriver again. Fit balancer shaft belt in anti-clockwise direction, starting at crankshaft sprocket. Slacken balancer shaft belt tensioner bolt. Turn tensioner clockwise to tension belt. Tighten bolt to 15-22Nm. Apply thumb pressure to belt. Belt should deflect 5-7 mm. If not repeat tensioning procedure. Install crankshaft sprocket guide washer, crnakshaft sprocket. Tighten crankshaft cente bolt. Tighten torque:110-130 Nm. Note ensure crankshaft sprocket guide washer is fitted correclty. Oil treads and contact face of crankshaft body before fitting. Check tensioner body for leakage or damage replace if necessary. Check pushrod protrusion is 12mm. If not replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Resistance should be felt. Place flat washer under tnesioner body to avoid damage to body end plugs. Retain pushrod with suitable pin through hole in tensioner body. install automatic tensioner unit to cylinder block. Tighten bolts to 22-27Nm. Fit timing belt in anti-clockwise direction, starting at the tensioner pulley. Slacken tensioner pulley bolt. Turn tensioner pully clockwise to temporarily tension belt. Tighten bolts to 43-45Nm. Turn crankshaft slowly 1/4 turn anti-cockwise. Turn crankshaft clockwise until timing marks alligned. Slacken tensioner pully bolt. Fit tool to tensioner pulley. Tool No 09244 28100. Apply clockwise torque of 2,6-2,8 Nm to tensioner pulley. Tighten bolt to 43-45Nm. Insert special tool in timing belt rear casing. Tool no 09244-28000. Screw in tool until pin can be removed from automatic tensioner unit. Remove special tool. Tool nr 09244-28000. turn crankshaft two turns clockwise. Wait 15 minutes. Ensure timing marks aligned. Check extended length of pushrod is 3,8-4,5mm. Install components in reverse order of removal. Tighten crankshaft pulley bolts, Tighten torque 20-30Nm

Nov 01, 2009 | 1995 Hyundai Elantra

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Do not know how to remove crankshaft pulley to replace timeing belt


Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Apr 30, 2009 | Plymouth Voyager Cars & Trucks

Not finding what you are looking for?
1990 Nissan Hardbody King Cab Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...