Question about 1995 Nissan Pickup

Open Question

My clutch doesnt engage i replaced slave cyclinder and bleed system but didnt replace spring for pedfal and now doesnt work

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 383 Answers

SOURCE: clutch slave cylinder

Yes, it is located on the passenger's side of the car at the front lower side of the transmission.
You will need the following tools: 12mm and 14mm socket. The slave cylinder could be bolted to the bell housing using either size bolt head.
A 14mm and 17mm open end wrench. The hose to the slave cylinder could be found with either size.
a 10mm combination wrench for the bleeder screw. A small set of vice grip pliers.
Removal and installation instructions for the slave cylinder:
1.Take the small set of vice grip pliers and adjust them to where they just barely close down on the slave cylinder hose. Just enough to pinch off the flow of fluid but not damage the hose.
2. Using the 14mm or 17mm open ended wrench, break the hose loose from the slave cylinder, turning it in a counter clockwise direction. Make sure you have the wrench squarely on the fitting to avoid rounding it off.
3. using either the 12 or 14mm socket, remove the two bolts which hold the slave cylinder to the bell housing.
4. At this point with the slave cylinder lose, have the replacement part near by, make sure you have the copper crush ring with it.
5. Holding the hose, rotate the slave cylinder counter clockwise, spinning it off the hose.
The replacement part should have a small metal rod and rubber cover which retains it to the slave cylinder. Make sure to remove the old copper crush ring and put the new one on the end of the hose. If the part did not come with one, reuse the old one. Spin the new part on the hose and place it back on the bell housing, making sure that the rod fits into the steel linkage which projects out from inside the transmission. There is a shallow hole which the rod should fit in. Holding the part in place, don't try to tighten the hose yet, screw both bolts in by hand and tighten them. Make sure you have them both in before you go tightening anything.
6. Tighten the hose, a good snug pull is all that is needed. you don't have to crank down on the line.
Now you can remove the pliers.
7. At this point you will need the assistance of another person. Have them sit in the car, you top off the clutch master cylinder (the one which has just one resevoir) with DOT 3 brake fluid. See if you can find a small container to catch the fluid in, or just use an oil drain pan. With you stationed under the car with the 10mm wrench on the bleeder screw ready to open it up in a counter clockwise direction, have your friend ready to pump the clutch pedal.
READY?
HAVE THEM PUMP THE PEDAL AND TELL THEM TO "HOLD IT" They should keep the pedal on the floor while you open the bleeder screw up.
Some fluid and air may or may not come out the first time you open the bleeder. Close it and tell them to pump the pedal again. They need to pump the pedal at least 5 times and them tell them to "Hold It" again, holding it to the floor. Don't open the bleeder until they have the pedal to the floor.
Open the bleeder and then close it. Repeat the procedure until you see just fluid and no air coming out.. After the first three times you bleed it, check the clutch master fluid level again. Avoid running the reservoir empty other wise you will be bleeding the cluch for quite a while.
Brake fluid will attack paint so if you spill any on the paint, pour water on it and it will neutralize it. DO NOT GET WATER IN YOUR BRAKE FLUID!!!!
If everything goes well, by the fourth or fifth time you have had them pumped the pedal, you will notice the slave cylinder is pushing the release arm and the person in the car should be feeling a normal clutch pedal along with the "pedal free play" being roughly 1/2 " from the top.
I hope I not only answered your question, but have supplied you all the necessary information should you be up to the task of changing it.

Posted on Apr 23, 2009

TwinTurboZ
  • 78 Answers

SOURCE: clutch 'pops' straight to the floor in my 93 300zx

The slave cylinder is replaced simply by removing 2 14mm or 12m nuts on the bottom side of the trans. There is no need for transmission removal.

Remember to point out to the shops that there are two bleeding points for the clutch. On the slave cylinder itself and under the hood on the passenger side. Its right behind the windshield washer fluid fill spot. Sometimes the bleeder is covered with a black cover.

Posted on May 23, 2009

  • 4088 Answers

SOURCE: hello i just replaced my

Have someone operate the clutch pedal several times while you watch the clutch arm that is connected to the slave. It should move back and forth. Manually check for free play at this arm--it probably should be about 1/4 inch or so. Is the slave body attached firmly to the transmission or bell housing? Fit a pry bar into the space around the clutch arm to prevent movement and test the clutch pedal for 'spongy' action--this would be air still in the system. Any missing springs around the slave? Put the truck in gear, push in the clutch--you should be able to move the truck without turning the engine. Don't try to drive until this operation works.

Posted on Aug 25, 2009

  • 507 Answers

SOURCE: 1994 Altima clutch master and slave replacement

easy replace both parts then fill the clutch reservoir,crack slave cly bleeder to let gravity bleed let 1 to 2 reservoirs flow through,tighten bleeder and pump clutch pedal,pump 4 or 5 times hold down pedal get 2nd person to crack bleeder while pedal is down,tighten bleeder before releasing pedal,should work fine

Posted on Nov 05, 2009

Testimonial: "Thanks, with your info I feel more confidant that I can replace the parts."

  • 110 Answers

SOURCE: how do you bleed cooling system for 1995 nissan pickup truck

  1. Open radiator cap and air relief plug.
  2. Fill radiator with coolant to specified level.
  3. Close air relief plug.
  4. Run engine and bring to operating temperature.
  5. Race engine two or three times under no-load.
  6. Stop engine and let cool, then add coolant as necessary.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My clutch pedal stay close to the floor in my Acura CL. Doesnt return fully like it used too. Cant figure it out and I've replaced everythin


Bobbie, If your sure the system is bled properly,did you get the clutch fork back in correct position, was it the correct bearing etc., you may have to adjust the clutch pedal and / or if it has a mechanical return spring, change the spring, it could be weak.
Check the attached links,instruction and guides for clutch pedal adjustment., bleeding,etc.Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Clutch Kit Installation Acura CL 2 2L 2 3L

Apr 02, 2016 | Cars & Trucks

1 Answer

I have a 87 5 speed pathfinder and the gears started to go on the transmission . now the transmision wont go into any gear.


Hi Robert,I have 85 Nissan 4x4,know these Nissan's very well,you stated your clutch fluid in reservoir was empty,which means your clutch slave cylinder is bad and leaking.It's located on the side of transmission with 2 bolts holding it on,may have fluid on it,they use brake fluid.Here's a guide on how to replace,here's the part,very easy to replace.You can fill up with fluid and bleed to get you where you need to go,will hold up temporary,best to get a bleeder kit at Autozone to bleed.

Mar 25, 2013 | 1988 Nissan Pathfinder

1 Answer

Ford 250 4x4 clutch ble to start truck


air in the line. you need to bleed the system

Mar 24, 2013 | 1992 Ford F250

1 Answer

I have a 1988 f350 diesel i replaced the clutch master cylinder and the slave cylinder bled the lines and the truck still wont go in gear the throw out arm is moving about 1/2 inch what could be my prob


Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

Jan 21, 2013 | Cars & Trucks

2 Answers

Lost resistance on clutch pedal and hard to change gears also when topping up clutch fluid it does`nt last that much and leaks from slave cyclinder


If the slave cylinder is leaking, replace the slave cylinder. You are loosing hydraulic pressure in the clutch and is the reason why it is not engaging correctly.

Apr 13, 2011 | 2001 Honda Accord

2 Answers

I just replaced the clutch, pressure plate, throwout bearing and both the master and slave cylinders. I am not getting any significant travel in the slave when I push the pedal in. How much travel should...


you may just open the bleeder, and let it gravity bleed. make sure on the master cylinder that the piston is coming all the way back when the pedal is all the way back/up. there's an adjustment for that, on the rod connecting the clutch pedal to the master cylinder.

Dec 21, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

There is no perssure in the clutch how do I fix


may also have air bleed clutch, or pressure spring collapsed or dislodged

Oct 28, 2009 | 1993 Honda Accord

3 Answers

Clutch pedal doesnt spring back up


Have you tried bleeding the clutch. Is it losing fluid?

May 03, 2009 | 1985 Toyota Celica Supra

2 Answers

1999 Dodge Ram 3500 Pickup - Clutch


use a hand vacumn and cover over the reservoir, apply light vacumn and the air will come to the reservoir, usually take 2 or 3 time and the air will work back out to the top,

Jun 05, 2008 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
1995 Nissan Pickup Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...