Question about 2000 Isuzu Rodeo

Open Question

Ignition problems coils

My ignition coils on a 2000 Isuzu rodeo is not firing at the same time. what could be the problem. I need help

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
snownbird33
  • 120 Answers

SOURCE: Holden 94 rodeo petrol

Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Posted on Sep 30, 2008

Ad
  • 393 Answers

SOURCE: 2000 isuzu rodeo brake problems

your master cylinder is gone. when stopped apply pedal and hold let up slightly then reapply if pedal sinks to floor master is bad.

Posted on Nov 16, 2008

  • 33 Answers

SOURCE: firing order 1995 isuzu rodeo 3.2v6

123456 IS THE FIRING ORDER... RIGHT BANK (RIGHT AS IN SITTING IN THE DRIVERS SEAT NOT STANDING IN FRONT OF THE CAR)STARTING AT FRONT IS CYLINDER 1 THEN 3 THEN 5 THEN THE LEFT BANK IS CYLINDER 2,4,6, FRONT TO REAR... THE COILS FROM LEFT TO RIGHT (STANDING IN FRONT OF CAR) ARE 1,4,6,3,2,5 HOPE THIS HELPS

Posted on Mar 27, 2009

Molson02536
  • 3854 Answers

SOURCE: 2000 Isuzu Rodeo speedometer and odometer notworking. fuel light flashing with gas in it

Go to Auto Zone and they'll scan the truck for you for free. If it's the speed sensor, that's not hard to replace, just unclip the wire harness and remove the old speed sensor on the left rear side of the put put shaft to the transmission. Auto zone caould give you more finer details on to how to do it your self instruction.
The fuel gauge sensor is a part of the fuel pump and that's going to be costly. If your luck it could just be a stuck float and in time the float me start working again. The other thing to is to check the wire harness from the frame rail to the gas tank, after time the winter salt carrodes the connection and it may need to be replaced.
I found most of the time when we work on changing the fuel pump, 65% of the time it's only the wire harness and the pump is fine. But customers always get the new pump and wire harness. 
Good luck and hope this helps.

Posted on Apr 22, 2009

ourhowse
  • 2007 Answers

SOURCE: 2000 isuzu Rodeo wont start

Could be your neutral safety switch, or it's not all the way in park. Broken or loose wires in the starting circuit. Inspect all wires and connectors at the battery, starter solenoid, and ignition switch. Or your starter pinion is jammed in the ring gear. Remove starter and inspect. Last but not least, your engine is seized. You don't want that one. Good luck.

Posted on May 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

COMMON CAUSES FOR MIS FIRING ON 1996 ISUZU RODEO V6


You fried the coil drivers , If you have B+ voltage going into those coils an they are new coils ,there is no control ! You have three wires to each coil ,one is B+ voltage ,one goes to what the wiring diagram calls a coil driver an the other looks like a ground symbol an says common chamber. You should be able to test for control with a test light. Go on youtube an watch a few scanner Danner videos on testing electronic ignition systems .

May 13, 2016 | 1996 Isuzu Rodeo

1 Answer

2002 isuzu rodeo will not start


Lots possible casues. Fuel pump may have failed. Check fuel pressure. A defective crank angle sensor will confuse the computer and cause it not to fire the ignition coils (no spark).

Mar 25, 2014 | 2002 Isuzu Rodeo

1 Answer

2000 isuzu rodeo only firing on 3 cylinders


You should have a check engine light on and a code for the dead cylinder. You'll need to figure out if it is mechanical, fuel, or ignition to proceed.

Feb 27, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

Can you cross reference this code p1340 on a 2000 isuzu rodeo check engine light on


code p1340 refers to ignition control module (ICM)-cylinder identification/ syncronization===causes--wiring--ignition coils--ICM---ECM Talk to the service dealer as to the most probable failed unit before you waste money

Dec 06, 2013 | 2000 Isuzu Rodeo

3 Answers

What is the firing order for isuzu rodeo 2002 2.2 lits


Please don't forget to rate! This helps us help you!!! Thanks!!


c17hydro_180.gif

2.2L VIN D engine Firing order: 1-3-4-2 Distributorless ignition system

May 12, 2011 | 2002 Isuzu Rodeo

1 Answer

I have a 2002 rodeo with ignition coil malfuntion code ,but i change a coil pack 2 times with a new ones ,spark plugs ,wires timing belt and the problem still there and now i don't know what its can...


try the coil module locatrd by the coil on top of the engine.
It's a little flat chip looking device that regulates the ignition system,should cost somewhere arround $22.00

Nov 25, 2010 | 1998 Isuzu Rodeo

1 Answer

Spark plug firing order


For the 1991 Isuzu Rodeo
I do not know if you have the 2.6L SOHC In-Line 4-Cylinder or the 3.1L V6; however I have included both below.


For the 2.6L:
Firing Order
:

1-3-4-2
Cylinders:
(back)
...4
...3
...2
...1
(front)
Ignition Coils:
(back)
[///]1....2
[///]3....4
(front)

For the 3.1L:
Firing Order:
1-2-3-4-5-6
Cylinders:
.....(back)
5...............6
3...............4
1...............2
Distributor:
.....(back)
..............(+)-screw
.........4
..3
...................5
2
.................6
........1
(+)-screw
.....(front)
Rotation: Clockwise

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Jul 29, 2010 | 1991 Isuzu Rodeo

1 Answer

Firing order for a 2000 isuzu rodeo v6 2 wheel drive


2000 Isuzu Rodeo LSE 2WD 3.2 liter DOHC V-6

7fa2a6a.gif


Hope helps (remember rated this).

Jul 19, 2010 | 2000 Isuzu Rodeo

1 Answer

MY 2001 ISUZU RODEO


you are having the same problems i'm having, there could be numerous of problem starting from the crankshaft position sensor, o2 sensor, a bad ignition coil. don't make the same mistake i did guessing what is wrong by buying parts here and there. Please TAKE IT TO THE DEALER! let them scan it only telling you what is giving you problems

Dec 29, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...