Question about 2005 Nissan Terrano 2.7

Open Question

Why is my terrano 2004 clutch pedal sticking short of the top position

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: clutch pedal sticks

it is the slave cylinder, just fixed that problem

Posted on Dec 20, 2008

Ad
  • 1214 Answers

SOURCE: clutch slipping

A clutch is usually adjusted from underneath the car if it's a mechanical clutch.

Your comment that there is very little play at the top indicates an improperly adjusted clutch. You should have about 1/2 - 3/4 inch of play before feeling the clutch in the pedal.

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 dodge ram 1500 with the 3.7L V6 5 speed manual. The truck drives and shifts fine but after driving for a while it won't be able to shift into or out of any gear.


the reason for hard shifting and selection when running is that the clutch shaft ( input shaft) is still turning even though the clutch pressure plate is released
it can be from oil/grease on the fly wheel /pressure plate face causing it to stick when hot
it may be from sticking clutch plate on the splines binding when hot
or it could be a dry spigot bush or failed bearing in the end of the crankshaft that positions the clutch shaft
check the pedal height adjustment and the position it is from the floor when starting to engage
It may be adjustment under the dash

May 18, 2015 | 2004 Dodge Ram 1500

2 Answers

What does a clutch pedal position switch do?


It tells the Powertrain Control Module (PCM) what position your clutch pedal is in (pretty much like the name implies). The PCM will not allow the starter to work unless the clutch pedal is in the down position. The purpose is to keep you from starting the engine with the clutch engaged so the vehicle doesn't jump forward and kill somebody when you twist the key.

Jan 29, 2012 | 2004 Dodge Neon

1 Answer

Clutch Dodge SX2.0 2004


Just to be sure recheck the fluid level of the mastercylinder again. If it is a little low refill with proper fluid, and work the clutch several times with parking brake set. Also check the clutch pedal bushings at the top of clutch pedal to make sure there is no sticking or excessive wear. If you find anything unusal about the bushings, they need to be replaced. Hope this will help you.

May 16, 2010 | 2004 Dodge Neon

2 Answers

How to repair clutch pedal safety start switch on Ford Truck F550, 1999


Clutch Pedal Position (CPP) Switch
The clutch pedal position switch (CPP) is controlled by the clutch pedal. Depressing the clutch pedal manually closes the CPP switch and allows engine cranking. The CPP switch will also deactivate the speed control system.
--------------------------------------------------------------------
303-14A: Electronic Engine Controls — Gasoline Engines 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Clutch Pedal Position (CPP) Switch Removal
  1. sxo~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always disconnect the battery ground cable prior to working on the electronic engine controls.
    Disconnect the battery ground cable; refer to Section 414-01 .
  1. Disconnect electrical connector from clutch pedal position switch (CPP) (9A837).
  1. Release the clutch pedal position switch (CPP) (11A152) from the orientation clip.
  1. Remove the plastic retainer.
    1. Push the lock tabs together.
    1. Slide the plastic retainer off the clutch pedal position switch.
  1. Remove the clutch pedal position switch.
Installation
  1. Follow the removal procedure in reverse order.

Feb 06, 2010 | 1999 Ford Super Duty F 550

1 Answer

I need to change the clutch interlock switch can you tell me how to fix it ?


The Clutch Pedal Position ( CPP ) Switch is near the brake pedal. It has a 6 pin connector on it ( all 6 pins are in a line ) that has 4 wires from it.
Black w/ white stripe is a ground
Tan w/ light blue stripe is the clutch pedal position sensor top travel
Black w/ white stripe is a ground
White w/ Black stripe is the clutch pedal position sensor bottom travel.
I think this is what you are talking about, if not please let us know

Dec 29, 2009 | 2004 Ford F150

2 Answers

My 2004 stick shift Saturn Ion has a problem getting into gear. I step on the clutch and the car turns on fine, but when I step on the clutch and try to shift it inot first gear it doesn't let me. Some...


you have a clutch hydraulic problem. have the clutch master cylinder replaced and the linkage adjusted if neccessary. you will be money ahead to have them replace the slave cylinder at the same time.

Sep 23, 2009 | 2004 Saturn ION

2 Answers

Nissan Terrano II 2.7TDi clutch drop


Hi I had a simular problem with my pedal sticking down it turned out to be a small white clip that had worn were the pedal return spring sits it had chaffed a recess in the white clip and was snagging, the clips are about £3.50 so its worth a look, best way i found was to take the pedal box out and do it dont forget the bolt above the pedal you can reach it with a socket, the other two hold the master cylinder on.
Phill

Apr 22, 2009 | 1999 Nissan Pathfinder

1 Answer

How to adjust clutch brake on a eaton 2800 series clutch which is installed in a 2004 sterling dump truck


This is from http://refrigeratedtrans.com/mag/transportation_replace_original_equipment/

"A good clutch adjustment begins by identifying the location of the bearing. It should be positioned 1/2" to 9/16" from the clutch brake."

"After the bearing is set, adjust the truck linkage to allow the clutch brake to squeeze a .010" feeler gauge between the bearing and clutch brake when the pedal is no more than 1" to 1.5" from the floor. Setting the clutch brake position too far from the floor reduces the stroke to the clutch and could cause release problems and reduce brake life.
All that remains is checking the free-pedal distance in the cab. With the pedal in the up position, there should be 1" to 3" of free pedal. The clutch is now adjusted correctly."

Apr 21, 2009 | 2004 Ford Super Duty F 450

1 Answer

2002 Civic Dx Clutch?


i have just replaced an 03 civic ex clutch and transmission bearings due to a customer being too harsh on it. It sounds like its got a little life left in it if you are easy on it. 

if there is adjustment in this model use the below walkthrough to adjust it.

adjust the clutch pedal, 

1. if you look up on the top of the clutch pedal, the first thing you should see if a clutch pedal position switch, and right behind it there is a locknut, looens the locknut. once you loosen it, back off on the pedal position switch or adjusting bolt untill it no longer touches the clutch pedal. 

2. now behind the clutch pedal, there is a pushrod. and on that pushrod, there is a locknut, loosen that locknut. Now turn the pushrod in or out to get the desired height and stroke at the clutch pedal. 

The freeplay is the amount of push on the clutch pedal to where is starts to have resistance from the top. I have usually been told it should be set at 1 1/2-2 inches of freeplay.

Once you set it, tighten the locknut on the pushrod. With the clutch pedal released, turn in the clutch pedal position switch untill it contacts the clutch pedal. then turn it an additional 3/4 to 1 turn. And tighten the locknut.

Now on top of the clutch pedal switch, there is a clutch interlock switch. Loosen the locknut on that switch. then press the clutch pedal to the floor.

release the clutch pedal 15-20 mm (0.59-0.79 in) from the fully pressed position, and hold it there. adjust the position of the clutch interlock switch so the engine will start with the clutch pedal in this position. then tighten the locknut on that switch.

Hope this helps 

Nov 28, 2008 | 2002 Honda Civic

Not finding what you are looking for?
2005 Nissan Terrano 2.7 Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...