Question about 2006 Nissan Murano

1 Answer

Lh front window stuck in down posistion on my 2006 murano

How can i remove the glass to get the regulator off?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Allot of times I have beat on the motor with a rubber mallet while holding the UP button to get the motor to go up so I can get to the regulator. If that don't work you are just going to have to reach inside and start unbolting what you can get to, to give you enough slack to get to the motor bolts.

Posted on Jun 16, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
oneStan
  • 430 Answers

SOURCE: How do you replace the rear window wiper on a 2006

Sure, you have to remove the outer blade by moving the plastic cover off of the mount location & then remove the nut. You'll need to remove the door trim panel once the back door is open, once removed you'll see the harness leading to the motor & the mounting bolts. once removed, it's a straight pull out & you are done. To remove the back door trim, you'll need to gently pry out the 2 lights with a padded flat screwdriver & disconnect the plug-in connector, push in on the little buttons at the bottom of the door and then pry the 1/2 " push in plugs out, (these are all reusable) remove the handle/grip by gently prying & the panel will more or less "pop" out of the holders. It's a push fit once the bottom retainers are removed. Good Luck

Posted on Jan 27, 2010

Testimonial: "Thank you I will try tomorrow."

oneStan
  • 430 Answers

SOURCE: how do you remove and replace the rear window

Remove the wiper blade by removing the plastic clip that covers the 10MM nut holding the wiper arm on. Just get hold of the very bottom of the clip & gently pull outwards & you'll be able to remove it completely.

Inside back hatch, remove the "hand hold" by just prying carefully. The 3/4" little plugs with an 1/8" area in the center-press on the center about 1/4" in and you can remove the entire plug. Just reset that prong you pushed in to the outside of the attaching plug & after installing, you press on it to lock it in place. Remove the 2 interior lights, simply use a nylon screwdriver to prevent scratches, or a regular screwdriver gently on the end away from the switch & pry gently, it will pop out-remove the wires noting the way they fit. Once all of those & the hand hole is removed, the panel more or less flips from the bottom where you removed the items, away from the bottom of the hatch. That will expose the wiper motor & since the outer arm has been removed, just unplug & remove the obvious bolts there & pull it out. good luck

Posted on Feb 16, 2010

Testimonial: "Thanks for all the help."

redneckrabbi
  • 35 Answers

SOURCE: window limit switch reset on 2006 murano

You can try disconnecting both battery cables from the battery and touching them together for about a minute and then hook them back up that should reset it. I did it in a few newer vehicles and it seemed to work.

Posted on Apr 04, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 GRAND CHEROKEE REMOVE DOOR GLASS


how to ? You or them? who is doing this? DIY?

front or rear. left or right.
the fsm covers this.
or for 15 bucks alldata.com? RTM?
wk jeep

qoute
1. Remove the outside rearview mirror (Refer to 23 -
BODY/EXTERIOR/OUTSIDE REARVIEW MIRROR
- REMOVAL).
2. Remove the front door glass (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - REMOVAL). below....
3. Remove the weatherstrip from the front glass run
channel.
4. Remove the nut (2) that secures the top of the
front glass run channel (1) to the inside door panel.
5. Loosen the nut (3) that secures the bottom of the
run channel to the keyed hole on the inside door
panel.
6. Lift the front glass run channel upward within the
door far enough to disengage the nut that secures
the bottom of the run channel to the keyed hole on
the inside door panel.
7. Remove the front glass run channel from the door.
(back in is longer story) FSM C23 pg 16

and 23page
1. Remove the outer belt weatherstrip (1) from the
front door.
2. Remove the trim panel from the inside of the front
door (Refer to 23 - BODY/DOOR - FRONT/TRIM
PANEL - REMOVAL).
3. Remove the speaker from the inside of the front
door (Refer to 8 - ELECTRICAL/AUDIO/SPEAKER
- REMOVAL).
4. Remove the watershield from the inside of the front
door (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD
- REMOVAL).
5. Using the regulator (4), move the front door glass
(2) up or down as required to access the two window
regulator glass clamp bolts (3).
6. Loosen the bolt in each of the window regulator
glass clamps far enough to release the door glass
from the clamps.
7. Disengage the door glass from the window regulator
glass clamps.
8. Lower the regulator down as required for access to remove the door glass.
9. Carefully rotate the door glass within the window opening and remove the glass from the door through the window
opening.

sorry tool lazy for photos today....

Jul 17, 2012 | 2012 Jeep Grand Cherokee

1 Answer

WHEN I ROLL UP THE DRIVER FRONT WINDOW IT GOES UP THEN ROLLS HALF WAY DOWN BY ITSELF


Hi there,

If manual window winder

Your driver's window glass may have come off the regulator mechanism.


If electric window control

The glass may have detached from the regulator or the regulator cable has unwound itself off the mechanism (ie tension during upward motion, but loose when motor stops winding).

Your driver's door panel will need to be removed to inspect your window regulator operation.

Jun 07, 2011 | 2006 Toyota Sequoia

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How do you replace a front drivers side power window motor? It is stuck all the way down and I can't pry it up. Is there a way to release it so I can get to the motor to replace it?


You have to remove the door panel. Remove the window from the regulator( two screws that hold the glass to the regulator) . Pull the glass up and wedge two pieces of wood from bottom of door to hold the window up.
Make sure its the motor thats giving you the headache and not the regulator. Regulator is notorious for snapping from the motor.

Apr 19, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

I need a left front door/window schematic on line for a 99 Dodge Durango. I need to see how to put it together.


Front Door
  1. Remove the door trim panel.
  2. Remove the water dam.
  3. Remove the inner and outer door belt weatherstrips.
  4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
  5. Remove the front glass run channel.
  6. Remove the nuts attaching the glass channel to regulator arm.
  7. Separate the glass and lift it up and out.
  8. Disengage the power window motor wire connector from the door harness, if equipped.
  9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
  10. Remove the bolts attaching window regulator to inner door panel.
  11. Remove the regulator through the access hole in the inner door panel.
  12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
3455a81.gif
Power window regulator mounting—Dakota, Durango

6125789.gif
Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Oct 26, 2009 | 1999 Dodge Durango

1 Answer

Window on my 2001 F150 went down & got stuck. Removed the panel and removed the glass from the track (taped up for now). It looks like I have to drill out rivets to remove the motor. The motor clicks on...


I am guessing that you have the door panel off already so take the window all the way up and take some duct tape and secure the window up all the way. Remove the front door window glass to regulator assembly bolts. Loosen the glass clamp fasteners through the 2 vertical slots in the inner door panel. To install tighten to 80 inch pounds. If equipped disconnect the front door window electrical connector. Remove the front door window regulator bolts to install tighten to 8 foot pounds. Remove the front door window regulator and motor. To install in reverse order.

Apr 16, 2009 | 2005 Ford F-150

1 Answer

How to replace window regulator


you will need to drill out some rivets. Replace with ntus and bolts and washers & lock washers. Make sure they don't hit glass going up and down. Otherwise you will need a heavy duty riveter.
please rate as fixya if this helps.

Motor —Front Door
Special Tool(s) swj~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal
NOTE: The window regulator and motor are removed as an assembly.
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the front door radio speaker.
  1. Remove the latch remote control. For additional information, refer to Section 501-14A .
  1. Remove the front door watershield.
  1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the window glass to avoid damage.
    Raise and support the front door window glass to the full up position.
  1. Disconnect the power window motor electrical connector.
  1. Remove the window glass to regulator nuts.
  1. Remove the motor and window regulator assembly.
    1. Drill out the rivets.
    1. Remove the motor and window regulator assembly.
88565ca.gif
  1. NOTE: Prior to motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind.
    Remove the power window motor.
    1. Remove the bolts.
    1. Remove the power window motor.

Mar 21, 2009 | 1998 Ford Expedition

1 Answer

2004 Mercury Monterey left frnt window sector gear R&R proceedure


are you a techie? You need a heavy duty riveter to do this repair. May have to rent or borrow from auto store.

here's the procedure



Front Door Trim Panel s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (251 KB) NOTE: LH side is shown. RH side is similar.
  1. Remove the parts in the order indicated in the following illustration and table.

    df2877a.gif

  2. Item Part Number Description 1 23942/23943 Mirror access panel 2 1722897 Cup assembly 3 W56904-S424 Window regulator control switch panel screws 4 14A665 Window regulator control switch panel
    Removal Note 5 W701930-S424 Front door trim panel screw 6 W701930-S424 Front door trim panel screw 7 N602703-S61 Front door trim panel screw 8 1723943 Front door trim panel 9 W705590-S300 Nut insert(s)
  1. To install, reverse the removal procedure.
Item 4: Window Regulator Control Switch Panel Removal Note
  1. If equipped, disconnect the electrical connector(s).
-----------------------------------------------------------------------------------
Door Window Glass — Front s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (328 KB)
Special Tool(s) s4w~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A)
  1. Remove the front door trim panel. For additional information, refer to Section 501-01 .
  1. Position the watershield aside.
  1. Remove the parts in the order indicated in the following illustration and table.

    To remove individual parts, only carry out the listed steps: Part Steps Front door window glass 1, 3 Front door window regulator 1-5 Front door glass run 1, 3, 6-8
    4be8135.gif
Item Part Number Description 1 W706495-5100 Rivet (2 required)
Removal Note
Installation Note 2 N8621986 Nut (3 required) 3 21410 Front door window glass 4 W706495-5100 Rivet (4 required)
Removal Note
Installation Note 5 23200 Front door window regulator
Removal Note 6 N800507-S Bolt (2 required) 7 21596 Front door glass run 8 — Front door glass run (Part of 21596)
  1. To install, reverse the removal procedure.
Item 1: Rivet Removal Note
  1. Connect the window control switch.
  1. Connect the battery.
  1. Position the door window glass halfway down to gain access to the door window glass rivets.
    • Remove the rivets.
9391398.gif Item 4: Rivet Removal Removal Note
  1. Remove the rivets.
Item 5: Front Door Window Regulator Removal Note
  1. Disconnect the electrical connector.
  1. s4w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Prior to power window motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind. Failure to place the regulator arms in a fixed position can cause the spring to suddenly release resulting in personal injury.
    NOTE: The counterbalance spring assists the window in the upward direction.
    Remove the bolts and the window regulator motor.
Item 4: Rivet Installation Note
  1. Using the special tool, install the rivets.
b4c4793.gif

Feb 21, 2009 | 2004 Ford Freestar

1 Answer

Rear passenger side window stuck in down position


1) Yes you are right to think that it is the regulator.
2) You can repair this.

Remove the screws that hold the door panel on.
Remove the door panel. There are alot of clips on the door panel that just need to be pulled out with panel while removing.
Remove debris shield.(plastic piece between door panel and door.
The regulator will be visible at this point.
Disconnect the electrical connector from the regulator. Separate Glass from regulator. Some use clips some use bolts to hold the glass to the regulator.
Remove regulator attaching bolts.

Thats it just reverse the procedure for installation.

Aug 29, 2008 | 2006 Jeep Liberty

2 Answers

Replacing window regulator


You can buy the plastic clips from the dealer, break the old ones, there is no tool that I remember using, in fact I don't remember having any problem, are you sure the regulator is at fault? why not just replace the motor?

Aug 25, 2008 | 2003 Dodge Caravan

Not finding what you are looking for?
2006 Nissan Murano Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...