Question about 2005 Hyundai Sonata

1 Answer

Need pictures of cv joints on 2005 sonota - 2005 Hyundai Sonata

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 2,984 Answers

need pictures of cv joints on 2005 sonota - de2de2e.jpg
Here ya go!

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 optima keeps going thru cv joints replaced 3 times 4 months what is goin on


The most common cause of failure is the rubber boot on the joint that is letting debris or water in the joint and letting grease out .If you are sure the boots and clamps on the boots are ok, then one of the shafts on the cv joint is out of balance or has a bad bearing.

Feb 26, 2015 | 2005 Kia Optima

1 Answer

2005 KIA SEDONA OUTPUT SHAFT SEAL


Hi Phil, On the Spyder end of the shaft that fits into the gearbox there is a retaining clip. Did you knock it in securely? If you did then a seal may have become damaged when making the replacement. That will need replacement. Regards John

Oct 27, 2012 | 2005 Kia Sedona

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

2 Answers

When I turn corners in my 03 aviator it makes a loud clicking noise rather I turn left or right. What can it be?


axle CV joints. Check 4 boots for tears. Also grab shafts and tug--check for play in joints. Replace axles that have play in CV joints. Let us know if you need instructions.

Oct 06, 2010 | 2005 Lincoln Aviator

1 Answer

Ford fusion front end noise when doing tight three point turn or manovers


popping noise when turning is usually caused by worn CV joints. Inspect CV boots for tears. Torn boot will allow dust to get in and cause wear. If boot is torn, replace CV joint or entire shaft (usually easier). If boot is not torn, grab shaft next to each CV joint and see how much movement you can cause in the joint. If one CV moves more than the other three, that one is probably bad.

Aug 23, 2010 | 2005 Ford Fusion

1 Answer

My Ford Focus C-Max has a leaking gator. What is this, what problems can it cause and how much to put right ?


I presume you mean a cv joint boot/gator. if not replaced the cv will run dry, can pick up dirt from the road ,etc, leadind to failure of the cv joint.

Oct 08, 2009 | 2005 Ford Focus

1 Answer

Hyundai 2005 Elantra cv boot replacement instructions.


There are no instructions available except with the purchase of SOME boot kits. Depending on the CV joint design, you may not be able to remove the joint from the axle. However, most Hyundai CV joints can be removed from the axle by using a drift and a 2 pound hammer to knock the joint off the axle. Once you've done this, it's a simple matter of removing the old boot and installing the new one w/fresh grease and tension bands. Otherwise, you have to remove the DOJ from the other end of the axle and replace the boot that way.

Aug 24, 2009 | 2005 Hyundai Elantra

1 Answer

How to replace a cv joint on a 2005 toyota corolla, i cant get the cv joint back part off the transmittion. driver side cv joint broke and rear part is stuck to transmittion..


There are two types of cv joints used. One type bolts on the other you have to pop out. Do this by prying it out with a big screwdriver. A c-clip hods it in and it will pop out for you. When reinstalling be sure it seats back in.

Jul 26, 2009 | Toyota Corolla Cars & Trucks

1 Answer

I need to change a cv joint on a 2005 cavalier


If it were me, I'd just change out the half shaft like THIS.

On the other hand, if you want to rebuild the CV joint, go HERE.

Nov 21, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...