Question about 1998 Mercury Tracer

Open Question

Picture of preasure swith 1998 mercury Tracer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mike258
  • 1498 Answers

SOURCE: serpentine belt for 1998 mercury tracer

Hey there MSM,

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator. The routing diagram is on one of the radiator supports.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

  • 297 Answers

SOURCE: Removal of front trans-axle of 94 mercury tracer

The center nut or the wheel bolts ?????

Posted on Aug 12, 2009

Testimonial: "center nut"

ZJLimited
  • 17970 Answers

SOURCE: I need a diagram of a how to install a serpentine

1998 MERCURY TRACER - L4 2.0L 1989cc 122ci GAS FI N P

Belt Routing Diagram / Multiple Accessory, w/A.C.

8e6e46f.jpg


More details HERE

I hope help you (remember rated this help) Good luck.

Posted on Sep 18, 2009

emissionwiz
  • 75235 Answers

SOURCE: were is the horn on a mercury tracer 1998

the horn is not the problem here, this is

In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Posted on Apr 03, 2010

ZJLimited
  • 17970 Answers

SOURCE: belt routing diagram for 1997 mercury tracer?

Check this...

f307936.gif

Hope helps.



Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show me the rear expansion plugs behind flywheel for a 98 mercury tracer 2.0l


Why----the trans axle has to come out to
get to them

This is a chat room/forum only

You need to use Google & the internet
for your questions,pictures & video

Sep 29, 2014 | 1998 Mercury Tracer

1 Answer

Looking for the starter relay in a 1998 tracer


1998 Mercury Tracer is equipped only with a 2.0L MFI SOHC SPI engine (Multiport Fuel Injection, Single OverHead Cam, Split Port Induction). This vehicle does not use a starter relay. Power from the ignition switch goes through the Clutch Switch (manual transmission) or the Neutral Safety Switch (automatic transmission) then directly to the solenoid at the starter. The solenoid is serviced only as part of the starter assembly. (SEE PICTURE)


dttech_180.gif

Aug 30, 2011 | 1998 Mercury Tracer

1 Answer

1998 mercury tracer evap canister needs to be replaced,where is that located


It's in the rear, driver side, near gas tank. under this plastic cover.




snorkelbobby_56.gif

May 13, 2011 | 1998 Mercury Tracer

1 Answer

Computer problems


its located below the center of the dash, heres a diagram to help pinpiont it, hope this is helpful.d3f9ae7.gif

Jan 24, 2010 | 1998 Mercury Tracer

1 Answer

Where can I buy fuses for my 1998 Mercury Tracer


i think theres a autozone store near you there? you can buy any part through them

Jan 22, 2010 | 1998 Mercury Tracer

1 Answer

1998 mercury tracer. overheated while waiting in


It might be a bad relay or a bad engine coolant temp sensor. Fan is likely good. Might have 2 relays. See owner manual.

Dec 14, 2009 | 1998 Mercury Tracer

1 Answer

I need a diagram of a how to install a serpentine belt on a 1998 Mercury Tracer with air.


1998 MERCURY TRACER - L4 2.0L 1989cc 122ci GAS FI N P

Belt Routing Diagram / Multiple Accessory, w/A.C.

8e6e46f.jpg


More details HERE

I hope help you (remember rated this help) Good luck.

Sep 18, 2009 | 1998 Mercury Tracer

1 Answer

Replacing timing belt


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 20, 2009 | 1998 Mercury Tracer

Not finding what you are looking for?
1998 Mercury Tracer Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...